FTSH-105-04-L-D Datasheet, PDF (1/3 Pages) Samtec, Inc – 050X050 CL THROUGH HOLE TERMINAL STRIP

REVISION BQ
DO NOT
SCALE FROM
THIS PRINT
SEE NOTE 3
(2 PLCS)
NOTES:
1C. REPRESENTS A CRITICAL DIMENSION.
2. PARTS MAY BE CUT TO POSITION.
3. MAXIMUM CUT FLASH: .010[0.25].
4. MINIMUM PUSHOUT FORCE: 1.0 LB.
5. TERMINALS TO BE SHEARED TO MEET DIMENSION SPECIFICATION.
6. LAYER PACKAGE 2 - 4 POSITIONS AND TUBE 5 - 50 POSITIONS.
7. MAXIMUM BURR ALLOWANCE: .003[0.08].
8. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -EC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -EC OPTION.
9. MAXIMUM HEIGHT VARIATION BETWEEN ROWS: .005[0.13].
(No OF POS x .0500[1.270]) - .003[0.08] .006 [0.15]
(No OF POS x .0500[1.270]) - .0500[1.270]
02
50
.135 3.43
REF
01
49
FTSHC-50-D
FTSH-1XX-XX-XXX-D-XX
No OF POSITIONS
-02 THRU -50
(PER ROW)
OPTIONS
-ES: END SHROUDS (SEE FIG 2, SHT 2)
(MOLDED 5 POS MIN; -02 & -03 LEAD STYLE ONLY)
LEAD STYLE
(MUST USE FTSH-XX-ES-XX-X)
-01: .120 [3.05]
(SNAP SHROUDS 9 POS MIN; -02 & -03 LEAD STYLE ONLY)
-02: .075 [1.91]
(MUST USE FTSH-50-D)
-03: .065 [1.65]
-EJ: EJECTOR SHROUDS: (SEE FIG 3, SHT 2)
-04: .150 [3.81]
(10 POS MIN; -01 LEAD STYLE ONLY)
(MUST USE FTSH-50-D)
-EC: LOCKING CLIP (SEE FIG 4, SHT 2; SEE NOTE 8)
PLATING SPECIFICATION
(9 POS MIN; -02 & -03 LEAD STYLES ONLY)
-G:10µ" GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
-F: 3µ" FLASH SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
-L: 10µ" LIGHT SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
(MUST USE FTSH-50-D)
-EP: GUIDE POST (SEE FIG 5, SHT 2)
(9 POS MIN; -02 & -03 LEAD STYLES ONLY)
(USE ONLY WHEN MATING WITH CLP)
(MUST USE FTSH-50-D)
-EL: BOARD LOCKS (SEE FIG 6, SHT 2)
(9 POS MIN; -02 & -03 LEAD STYLES ONLY)
(USE ONLY WHEN MATING WITH CLP)
(MUST USE FTSH-50-D)
-H: 30µ" HEAVY GOLD IN CONTACT AREA,
-K: KEYING OPTION FOR MATING WITH FFSD
3µ" GOLD ON TAIL
(05 THRU 25 ONLY)
-FM: 3µ" FLASH SELECTIVE GOLD IN CONTACT
(POSITION 13, 17, 20 & 25 AVAILABLE WITH -EJ OPTION)
AREA, MATTE TIN ON TAIL
(LEAD STYLE -01 ONLY, SEE FIG 7, SHT 3)
-LM: 10µ" LIGHT SELECTIVE GOLD IN CONTACT
(MUST USE FTSH-XX-CN-XX)
AREA, MATTE TIN TAIL
-LC: LOCKING CLIP: (SEE FIG 8, SHT 3)
-SM: 30µ" HEAVY SELECTIVE GOLD IN CONTACT
(5 POS MIN, ONLY AVAILABLE IN -01 LEAD STYLE)
AREA, MATTE TIN ON TAIL
(IN COMBINATION WITH -K, USE FTSH-XX-CN-XX,
-LTL: 10µ" LIGHT GOLD IN CONACT AREA,
10 POSITION MINIMUM, ONLY AVAILABLE IN
TIN/LEAD (90%/10 +/-5%) ON TAIL
-01 LEAD STYLE)
(MUST USE FTSH-50-D)
ROW SPECIFICATION
-D: DOUBLE ROW
(SINGLE MATING CYCLE ONLY)
(MUST BE MATED TO SAMTEC FFSD SERIES)
(USE **FTSHC-1XX-XX-XXX-D UNLESS OPTION IS SPECIFIED ABOVE. WHEN OPTION IS SPECIFIED,
BUILD PER PRINT USING BODY SPECIFIED FOR REQUIRED OPTION)
** = SEE FTSHC-1XX-XX-XXX-DX-XX PRINT FOR DETAILS
.0160 0.406 SQ
REF (TYP)
2 MAX SWAY
(EITHER DIRECTION)
"A" ^C
(SEE TABLE 1)
(SEE NOTE 9)
.099 2.51
"B"
(SEE TABLE 2)
(SEE NOTES 5 & 7)
C
.050 1.27
2 MAX SWAY
(EITHER DIRECTION)
T-1S15-XX-XXX
SEE TABLE 1
"C" REF
(SEE TABLE 1)
"A"
(SEE TABLE 1)
(SEE NOTE 9)
FIG 1
(SEE FTSHC-1XX-XX-XXX-DX-XX-PRINT FOR DETAILS)
2 MAX SWAY
(EITHER DIRECTION)
IN-PROCESS
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [.3]
1
.XXX: .005 [.13]
.XXXX: .0010 [.025]
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MATERIAL:
DO NOT SCALE DRAWING
INSULATOR: LCD UL 94-V0
TERMINAL: PHOSPHOR BRONZE
SHEET SCALE: 5:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail [e-mail] code 55322
DESCRIPTION:
.050 x .050 CL THROUGH HOLE TERMINAL STRIP
DWG. NO.
FTSH-1XX-XX-XXX-D-XX
F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-D-XX-MKT.SLDDRW
BY: J. FERRY 02/27/1996 SHEET 1 OF 3