CRIMP-SPECIFICATIONS Datasheet, PDF (1/4 Pages) Samtec, Inc – CRIMP/STRIP SPECIFICATIONS

REVISION AI
DO NOT
SCALE FROM
THIS PRINT
"D"
"B" REF
REF
FOR CRIMP INSPECTION CALLOUTS
CUT CABLE
CONTACT/TERMINAL - LEAD STYLE - CRIMP - AWG - CABLE TYPE _BWC-01-04-01
TABLE 5
DEPTH/DIMENSION
0.55[14MM]
"A"
SECTION "A"-"A"
SCALE 3 : 1
WIRE CRIMP
"C"
SECTION "B"-"B"
SCALE 3 : 1
INSULATION CRIMP
SEE
TABLE 1
FOR EXAMPLE, IF INSPECTING A CRIMP OF
C-179-02-X WITH 26AWG DWC, THE
CALLOUT FOR INSPECTION WOULD BE
"C-179-02-CRIMP-26-DWC"
BWC-01-16-01
BWC-02-10-01
BWC-02-32-01
BWC-05-14-01
UCA-01-01
UCA-02-01
1.34[34MM]
0.71[18MM]
1.18[30MM]
0.31[18MM]
0.47[12MM]
0.55[14MM]
UCA-03-01
0.63[16MM]
ECA-01-01
0.79[19MM]
ECA-02-02
0.79[19MM]
CONTACT
TERMINAL
SCTP-05-02
SCTP-08-02
0.83[21MM]
1.10[28MM]
LSPC-26100-05-P5-H
1.10[28MM]
"A"
"B"
"A"
"B"
"A"
"B"
"A"
"B"
"H" MAX
(TAB LENGTH)
LSPC-26100-08-H
LSPC-26100-12-H
STCP-08-01
SCTP-12-01
SCTP-16-01
1.26[32MM]
1.57[40MM]
0.91[23MM]
1.06[27MM]
1.18[30MM]
SCTP-24-01
1.42[36MM]
"J" MAX
(BURR ALLOWANCE)
LSPC-30100-05-P5-H
LSPC-26100-09
LSPC-26100-08-P5-H
0.79[20MM]
1.18[30MM]
1.18[30MM]
XWCX-XX-XX-XXX
FIG. 3
(CARRIER TAB
SPECIFCATION)
LSPC-26100-08
LSPC-26100-12
CABLE CUT IN-PROCESS
1.10[28MM]
1.26[32MM]
XWCX-XX-XX-XXX
FIG 1
* CUT LENGTH IS ASSEMBLY
LENGTH MINUS OVERALL
LENGTH SUBTRACTOR
"E"
"E"
"E"
OVERALL LENGTH "F"
SEE TABLE 4
OVERALL LENGTH "G"
SEE TABLE 4
OVERALL LENGTH "H"
SEE TABLE 4
NOTES:
1.
REPRESENTS A CRITICAL DIMENSION.
2. ALL CRIMP AND STRIP DIMENSIONS SHOWN
SHALL SUPERCEDE ANY EQUIVALENT
SPECIFICATIONS THAT ARE SUPPLIED BY
TOOLING MANUFACTURER.
3. FOR LENGTHS LESS THAN 12 IN, TOLERANCE
SHALL BE +/-.125. FOR OTHER LENGTHS, TOLERANCE SHALL BE +/-2%.
4. MAXIMUM BURR ALLOWANCE: .003 [.08]
5. PULL FORCE MUST MEET REQUIRED TABLE 1 SPECIFICATION FOR WIRE
GAUGE BEING USED.
"E"
"E"
-S: SINGLE END
-D: DOUBLE END
FIG 2
IN-PROCESS
-T: TRANSFER END
UNLESS OTHERWISE SPECIFIED,
PROPRIETARY NOTE
DIMENSIONS ARE IN INCHES.
THIS DOCUMENT CONTAINS INFORMATION
TOLERANCES ARE:
DECIMALS
ANGLES
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
.XX: .01 [.3]
2
.XXX: .005 [.13]
.XXXX: .0020 [.051]
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.571429
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail: [e-mail]
code: 55322
DESCRIPTION:
CRIMP/STRIP SPECIFICATIONS
DWG. NO. _{CRIMP-SPECIFICATIONS}
F:\DWG\MISC\MKTG\CRIMP-SPECIFICATIONS-MKT.SLDDRW
BY: D.SCHMELZ 10-11-2010 SHEET 1 OF 4