ASP-149118-01 Datasheet, PDF (1/2 Pages) Samtec, Inc – REPRESENTS A CRITICAL DIMENSION

ASP-149118-01
REVISION
"A"
CL
R2.30 (4 PLCS)
CL
NOT RELEASED
FOR PRODUCTION
USE FOR QUOTING, PRELIMINARY
DESIGN, PROTOTYPING AND
INFORMATIONAL PURPOSES ONLY
M1.60 x 0.35
THRU (2 PLCS)
3.24 (TYP)
8.000
TRUE R1.30 (8 PLCS)
"A"
28.00±0.10
14.00
CL
26.63
29.31
-W-
-X-
0.10 ^"B"
-Y-
8.87±0.10
4.50
"B"
14.82
13.62
0.10
-Z-
0.70 (2 PLCS)
32.49
3.00
(2 PLCS)
18.12
R1.00
(TYP)
SEE NOTE 2
R1.50
(TYP)
6.0 (TYP)
11.25
5°
C1
2.400 (2 PLCS)
0.10 W X Y
M1.6 x 0.35 4.50
(2 PLCS)
26.00
CL
24.75
26.91
9.874
13.87
R0.50
(TYP) _8.50
C2
M1.6 x 0.35 3.80 (2 PLCS)
0.10 W X Y
NOTES:
1. ^C REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC SHALL APPEAR ON SURFACE SHOWN, APPROXIMATELY
3. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN 0.05 OFF THE
SURFACE OF THE PART.
4. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCRATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
5. PARTS TO BE PACKAGED IN TRAYS.
6. ALL DRAFT MUST BE WITHIN TOLERANCES.
7. PARTS TO BE SHOT BLASTED.
8. DIMENSION TO BE ADJUSTABLE IN THE DIE.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN MILLIMETERS.
TOLERANCES ARE:
DECIMALS
X.X: 0.3
X.XX: 0.13
X.XXX: 0.025
ANGLES
2
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MATERIAL:
DO NOT SCALE DRAWING
ZAMAK 3
PLATING:
Cu: 0.008 - 0.015 mm [.0003 - .0006 in.] UNDERPLATE
Ni: 0.003 - 0.008 mm [.0001 - .0003 in.]
MAX GATE VESTIGE: 0.13
MAX FLASH ALLOWED: 0.08
SHEET SCALE: 2:1
F:\DWG\SW\Newprod\Pt635mm\HyperTransport\ASP-149118-01.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail: [e-mail]
code: 55322
DESCRIPTION:
0.635MM EDGE MOUNT PCB CAGE
DWG. NO. _{ASP-149118-01}
BY: VICKY Z
12/09/2009 SHEET 1 OF 2