ASP-137971-01 Datasheet, PDF (1/2 Pages) Samtec, Inc – ITEM 1 IS NOT AVAILABLE AS A STANDARD

ASP-137971-01
REVISION
NOTES:
1. ITEM 1 IS NOT AVAILABLE AS A STANDARD
2. C REPRESENTS A CRITICAL DIMENSION.
3. MAXIMUM BURR ALLOWANCE: .038[.0015].
4. MINIMUM PUSHOUT FORCE: 2.22N [.5 LB].
5. PARTS TO BE PACKAGED IN TRAYS.
17.80 .701 REF
((11 POS X .800[.0315]) + 9.00[.354])
C14
3
(SHORT PIN)
3 ^C15
(LONG PIN)
'D'
3.25 .128
REF
12.85 .506
01
C13
21
5.60 .220
REF
C16
2
DETAIL 'D'
SCALE 6 : 1
C1 _{0.800 .031}
(TOL. NON-ACCUM)
4
02
22
C2
8.000 .3150
13.00 .512 REF
12.90 .508
"A"
"B"
'C'
1.10 .043
REF
DETAIL 'C'
SCALE 6 : 1
0.65 .026 REF
(APPLIES TO ALL OTHER SIGNALS)
ODD ROW (DP SIDE, HOT PLUG SIDE)
C8
3.20±0.05 .126±.002
1.35 .053 REF
(APPLIES TO DP SIGNALS)
7.75 .305
REF
0.20 .008
REF
1
C6
2.50 .098
0.90 .035
C7
"A"
"B"
C4
8.000 .3150
C5
14.79±0.33 .582±.013
EVEN ROW
5.20 .205
REF
C3
0.800 .0315
TOL-NON ACCUM
C9
2.77 .109
C11
3.11 .122
C12
3.01 .119
C10
1.30±0.20 .051±.008
1.80 .071 REF
SECTION "A"-"A"
CL
1.47 .058
SECTION "B"-"B"
8.77 .345 REF
UNLESS OTHERWISE SPECIFIED,
PROPRIETARY NOTE
DIMENSIONS ARE IN MILLIMETERS. THIS DOCUMENT CONTAINS INFORMATION
TOLERANCES ARE:
DECIMALS
ANGLES
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
.X: .3[.01]
2
D
.XX: .13[.005]
.XXX: .051[.0020]
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: [phone] FAX: [phone]
e-Mail: [e-mail]
code: 55322
DO NOT SCALE DRAWING
PLATING:
CONTACT AREA: .000030 GOLD OVER .000050 NICKEL
REMAINDER: .000200 REF TIN OVER .000050 NICKEL
LATCHES: .000003 GOLD OVER .000050 NICKEL
SHEET SCALE: 1:0.3333D33ESCRIPTION:
MODIFIED ERM8 ASSEMBLY
DWG. NO. _{ASP-137971-01}
F:\DWG\SW\ASP\137000\ASP-137971-01.SLDDRW
BY: David F
01/30/2008 SHEET 1 OF 2