RV7-2403S30A1W Datasheet, PDF (2/4 Pages) RSG Electronic Components GmbH – DC/DC-Converter

63.00.W0WR4e:g1uRlaetgeudlaStinegdle &
DSiunagleO&utDputal Output
DC/DC-Converter
we weneeerngeizrgeizeeleecltercotnroicnsic!s!
an acal group company
RV7 - XX XX
X
Input
Type
XX
A X WX
Power (W) Code
internal
Isolation
(kVDC)
100%
W = 4:1 input Range
K = Option mit ^75%
Kühlkörper
50%
25%
Derating Curve
S.O.A.
wit hout heat sink
with heat sink
-40 -20
55
0
20
40
60
85
80 100 120
AMBIENT TEMPERATURE(°C)
MODEL SELECTION GUIDE
MODEL NUMBER
RV7-2403S30A1W
INPUT
INPUT Current
Voltage Range No-Load Full Load
(Vdc)
(mA, max.) (mA, typ.)
9-36, 24V Nominal
10
1093.75
RV7-2405S30A1W 9-36, 24V Nominal
10
1404.49
RV7-2412S30A1W 9-36, 24V Nominal
10
1404.49
RV7-2415S30A1W 9-36, 24V Nominal
10
1373.62
RV7-4803S30A1W 18-75, 48V Nominal
8
540.73
RV7-4805S30A1W 18-75, 48V Nominal
8
694.44
RV7-4812S30A1W 18-75, 48V Nominal
8
694.44
RV7-4815S30A1W 18-75, 48V Nominal
8
679.34
RV7-2412D30A1W 9-36, 24V Nominal
10
1404.49
RV7-2415D30A1W 9-36, 24V Nominal
10
1373.62
RV7-4812D30A1W 18-75, 48V Nominal
8
694.44
RV7-4815D30A1W 18-75, 48V Nominal
8
686.81
OUTPUT
Voltage
(Vdc)
3.3
5
12
15
3.3
5
12
15
±12
±15
±12
±15
OUTPUT Current
Min. load Full load
(mA)
(mA)
0
7000
EFFICIENCY
@FL
(%, typ.)
88
Capacitor
Load @FL
(µF, max.)
10000
0
6000
89
7200
0
2500
89
1200
0
2000
91
1000
0
7000
89
10000
0
6000
90
7200
0
2500
90
1200
0
2000
92
1000
0
±1250
89
±750
0
±1000
91
±500
0
±1250
90
±750
0
±1000
91
±500
1. One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%.
2. Tested by minimal Vin and constant resistive load.
3. Tested by normal Vin and 25% load step change ( 75%-50%-25% of Io ).
4. Measured Input reflected ripple current with a simulated source inductance of 12uH and a source capacitor Cin(47uF, ESR<1.0© at 100KHz).
5. The remote on/off control pin is referenced to -Vin(pin2).
6. Exceeding the absolute ratings of the unit could cause damage. It
is not allowed for continuous operating.
7. "Nature Convection" is usually about 30-65 LFM but is not equal to still air (0 LFM).
8. Input filter components are used to help meet conducted emissions,
Which application refer to the EMI Filter of design & feature configuration.
9. An external filter capacitor is required if the module has to meet EN61000-4-4,EN61000-4-5.
The RV7-24XXXX30 recommended an aluminum electrolytic capacitor ( Nippon chemi-con KY series, 330uF/100V) and a
TVS (SMDJ58A,58V,3000Watt peak pulse power) to connect in parallel.
The RV7-48XXXX30 recommended an aluminum electrolytic capacitor ( Nippon chemi-con KY series, 330uF/100V) and a
TVS (SMDJ120A,120V,3000Watt peak pulse power) to connect in parallel.
RSG Electronic Components GmbH • Sprendlinger Ldst. 115 • 63069 Offenbach •[phone] • Rsg-electronic.de
page 2 (4)