RS5-R30-RD30 Datasheet, PDF (1/4 Pages) RSG Electronic Components GmbH – 3.0 Watt 2:1 regulated single & dual output

RS5-R30/RD30
3.0 Watt 2:1 regulated
single & dual output
■ _{8 Pin SIP8 package}
■ _{Wide 2:1 input range}
■ _{1600 VDC isolation}
■ _{Continuous short circuit protection}
■ _{Efficiency up to 84%}
■ _{-40°C~71°C operation temperature range}
■ _{Metal case, Remote On/Off optional}
OUTPUT SPECIFICATIONS
Voltage accuracy
± 1%
Line regulation
± 0.5%
Load regulation (From 25% to 100% Load)
± 1%
Cross regulation (dual output)
± 5%
Ripple & Noise (20 MHz bandwith) (1)
75 mV pk-pk
Short circuit protection Indefinite (automatic recovery)
Temperature coefficient
± 0.02%/°C
Capacitor load (2)
See table
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
See table
See table
See table
Capacitors
35 mA pk-pk
ABSOLUTE MAXIMUM RATINGS (4)
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
5 modes
-0.7 ~ 15 VDC
12 modes
-0.7 ~ 36 VDC
24 modes
-0.7 ~ 50 VDC
48 modes (SIP) -0.7 ~ 100 VDC
Lead soldering temperature 260°C
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
Efficiency
See table
I/O isolation voltage (3 sec.) Input / Output 1600 VDC
I/O isolation capacitance
680 pF max.
I/O isolation resistance (min.)
1000 M Ohm
Switching frequency (min.)
100 kHz
Humidity
95% rel. H
Reliability calculated MTBF
> 2.465 Mhrs. @25°C
Safety standard (designed to meet)
IEC 60950
PHYSICAL SPECIFICATIONS
Case material
Pin material
Non-conductive black plastic
C5191R-H solder-coated
Potting material
Epoxy (UL94V-0 rated)
Weight
Dimensions
4.8 g, typ.
SIP > 0.86“ x 0.36“ x 0.44“
ENVIRONMENT SPECIFICATIONS
Operating temperature
-40°C~ 71°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
NOTE
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH and source capacitor Cin (47uF,
ESR < 1.0 Ohm @100 kHz).
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation at no-load conditions will not damage these
devices. However they may not meet all listed
specifications.
Transient Recovery Time 300 us typ., Transient Response
Deviation ± 3% max., Test by normal Vin and 100% -
25% load, 25% load step change.
Remote ON / OFF control
ON: open or high impedance
OFF: 3.0~6.0 mA input current (via 1K)
EMI CHARACTERISTICS
Conducted Emissions (10)
Radiated Emissions
EN55022
EN55022
CLASS A
CLASS A
ESD
IEC61000-4-2 Perf.Criteria B
RS
IEC61000-4-3 Perf.Criteria A
EFT (11)
Surge (11)
CS
IEC61000-4-4 Perf.Criteria B
IEC61000-4-5 Perf.Criteria B
IEC61000-4-6 Perf.Criteria A
PFMF
IEC61000-4-8 Perf.Criteria A
Input filter components are required to help meet Conducted Emission
class A, which application refer to the EMI filter of design & feature
configuration.
An external filter capacitor is required if the module has to meet EN61000-
4-4 and EN61000-4-5.
Page: 1/4
Last update: 30.01.09