RR7-S06-D06 Datasheet, PDF (1/3 Pages) RSG Electronic Components GmbH – 6 Watt 4:1 regulated single & dual output

RR7-S06/D06
6 Watt 4:1 regulated
single & dual output
■ _{DIP24, wide 4:1 input range}
■ _{Full SMD technology}
■ _{1500 VDC isolation up to 3500 VDC isolation}
■ _{Continuous short circuit protection}
■ _{Efficiency up to 84%}
■ _{-40°C~85°C operation temperature range}
■ _{Optional Plastic case}
■ _{EMI complies with EN55022 Class A}
OUTPUT SPECIFICATIONS
Voltage accuracy
± 1%
Line regulation
± 0.5%
Load regulation
± 0.5%
(Output 3.3V / ±3.3V Model)
± 1.5%
Ripple & Noise (20 MHz bandwith) (1)
60 mV pk-pk
Short circuit protection Indefinite (automatic recovery)
Temperature coefficient
± 0.02%/°C
Capacitor load (2)
See table
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
See table
See table
See table
PI Type
35 mA pk-pk
GENERAL SPECIFICATIONS
Efficiency (typ.)
See table
I/O isolation voltage (3 sec.) Input/Output 1500 ~ 3500 VDC
Metal case / input & output
1000 VDC
I/O isolation capacitance
500 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
typ. 266 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F) > 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1: 2001
PHYSICAL SPECIFICATIONS
Case material
Nickel-coated copper
Non-conductive black plastic
(UL94V-0 rated)
Base material
Non-conductive black plastic
(UL94V-0 rated)
Pin material
Ø 0.5 mm brass solder-coated
Potting material
Epoxy (UL94V-0 rated)
Weight
Metal 17.0 g, Plastic 13.5 g
Dimensions
1.25“ x 0.8“ x 0.4“
EMC SPECIFICATIONS
Radiated Emissions
EN55022
Conducted Emissions (4) EN55022
ESD
IEC61000-4-2
RS
IEC61000-4-3
EFT
IEC61000-4-4
CS
IEC61000-4-6
PFMF
IEC61000-4-8
Class A
Class A
Perf. crit. B
Perf. crit. A
Perf. crit. B
Perf. crit. A
Perf. crit. A
ABSOLUTE MAXIMUM RATINGS (4)
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
24 modes
-0.7 ~ 40 VDC
48 modes
-0.7 ~ 80 VDC
Lead soldering temperature 260°C
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
NOTE
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistor load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) It´s recommended to add C1 (68 F), C2 (33 F), L (12 H) in
input end to achieve EN55022 conducted Class A.
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve)
-40°C~ 85°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
The models listed are just for standard type. If you need a special
specification product, please contact our service.
Phone: [phone], mail to: [e-mail] or use the forms
on www.rsg-electronic.de („Kontakt“).
Page: 1/3
Last update: 18.02.10