PBA150F_14 Datasheet, PDF (1/14 Pages) RSG Electronic Components GmbH – AC-DC Power Supplies Enclosed type

AC-DC Power Supplies Enclosed type
Ordering information
PBA10F
PB A 10 F -O -O
1
2
3
4
5
6
PBA/PBW
R
Recommended EMI/EMC Filter
NAC-06-472
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
*The EMI/EMC Filter is recommended
*to connect with several devices.
1Series name
2Single output
3Output wattage
4Universal input
5Output voltage
6Optional *5
C :with Coating
G :Low leakage current
E :Low leakage current
and EMI class A
T :Vertical terminal block
J :Connector type
N :with Cover
(UL508 is acquired)
N1 :with DIN rail
V :Output voltage setting
potentiometer external-
ly
Cover is optional
MODEL
MAX OUTPUT WATTAGE[W]
DC OUTPUT
PBA10F-5
10
5V 2A
PBA10F-12
10.8
12V 0.9A
PBA10F-24
12
24V 0.5A
SPECIFICATIONS
MODEL
PBA10F-5
PBA10F-12
PBA10F-24
VOLTAGE[V]
CURRENT[A]
AC85 - 264 1f or DC110 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *3)
ACIN 100V 0.30typ (Io=100%)
ACIN 200V 0.20typ (Io=100%)
FREQUENCY[Hz]
50/60 (47 - 440) or DC
INPUT
EFFICIENCY[%]
ACIN 100V 74typ
ACIN 200V 74typ
76typ
76typ
77typ
77typ
ACIN 100V 15typ (Io=100%)
INRUSH CURRENT[A] _{ACIN 200V 30typ (Io=100%)}
LEAKAGE CURRENT[mA] 0.15/0.30max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN)
VOLTAGE[V]
5
12
24
CURRENT[A]
2
0.9
0.5
LINE REGULATION[mV] *6 20max
48max
96max
LOAD REGULATION[mV] *6 40max
100max
150max
RIPPLE[mVp-p]
0 to +50C*1 80max
-10 - 0C*1 140max
120max
160max
120max
160max
OUTPUT
RIPPLE NOISE[mVp-p] ^{0 to +50C*1 120max}
-10 - 0C*1 160max
150max
180max
150max
180max
TEMPERATURE REGULATION[mV] ^{0 to +50C 50max}
-10 to +50C 60max
120max
150max
240max
290max
DRIFT[mV]
*2 20max
48max
96max
START-UP TIME[ms]
HOLD-UP TIME[ms]
200typ(ACIN 100V, Io=100%) *Start-up time is 700ms typ for less than 1minute of applying input again from turning off the input voltage.
20typ (ACIN 100V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 4.50 - 5.50
10.0 - 13.2
19.2 - 27.0
OUTPUT VOLTAGE SETTING[V] 5.00 - 5.15
12.00 - 12.48
24.00 - 24.96
OVERCURRENT PROTECTION Works over 105% of rated current and recovers automatically
PROTECTION _{OVERVOLTAGE PROTECTION[V] 5.75 - 7.00}
CIRCUIT AND
OTHERS ^{OPERATING INDICATION}
LED (Green)
15.0 - 18.0
REMOTE ON/OFF
None
30.0 - 37.0
INPUT-OUTPUT
ISOLATION INPUT-FG
OUTPUT-FG
OPERATING TEMP.,HUMID.AND ALTITUDE
STORAGE TEMP.,HUMID.AND ALTITUDE
ENVIRONMENT
VIBRATION
AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature)
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature)
AC500V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature)
-10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max
-20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max
10 - 55Hz, 19.6m/s² (2G), 3minutes period, 60minutes each along X, Y and Z axis
IMPACT
196.1m/s² (20G), 11ms, once each X, Y and Z axis
SAFETY AND ^{AGENCY APPROVALS (At only AC input)}
NOISE
CONDUCTED NOISE
REGULATIONS _{HARMONIC ATTENUATOR}
OTHERS
CASE SIZE/WEIGHT
COOLING METHOD
UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN
Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
Complies with IEC61000-3-2 (Not built-in to active filter *4) *7
31X78X68mm [1.22X3.07X2.68 inches] (without terminal block) (WXHXD) / 150g max (without cover)
Convection
*1 Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN
:RM101).
*2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C.
*3 Derating is required.
*4 When two or more units are used,they may not comply with the harmonic attenuator. Please
contact us for details.
*5 Please contact us about safety approvals for the model with option.
*6 Please contact us about dynamic load and input response.
*7 Please contact us about class C.
* Parallel operation with other model is not possible.
* Derating is required when operated with cover.
* A sound may occur from power supply at peak loading.
PBA/PBW-2