LEP240F Datasheet, PDF (1/6 Pages) RSG Electronic Components GmbH – AC-DC Power Supplies Open Frame/ Enclosed type

LEP
AC-DC Power Supplies Open Frame/ Enclosed type
Ordering information
LEP100F
LEP 100 F -24 -O
1
2
3
4
5
1Series name
R
Recommended EMI/EMC Filter _{2Output wattage}
NAC-06-472
3Universal input
4Output voltage
5Optional *1 *6
G :Low leakage current
R :with Remote ON/OFF
S :with Chassis
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
*The EMI/EMC Filter is recommended
*to connect with several devices.
SN:with Chassis & cover
T :Vertical terminal block
U :Operating stop voltage
is set at a lower value
Z :with ZT
MODEL
DC OUTPUT
LEP100F-24
+24V 4.2(Peak 7)A
LEP100F-36
+36V 2.8(Peak 4.7)A
LEP100F-48
+48V 2.1(Peak 3.5)A
SPECIFICATIONS
MODEL
LEP100F-24
LEP100F-36
LEP100F-48
VOLTAGE[V]
CURRENT[A]
AC85 - 264 1f or DC 120 - 370
ACIN 100V 1.4typ (Io=100%)
ACIN 200V 0.7typ (Io=100%)
FREQUENCY[Hz]
50/60 (47 - 63) or DC
INPUT
EFFICIENCY[%]
ACIN 100V 81typ (Io=100%)
ACIN 200V 84typ (Io=100%)
82typ (Io=100%)
85typ (Io=100%)
83typ (Io=100%)
85typ (Io=100%)
POWER FACTOR
ACIN 100V 0.98typ (Io=100%)
ACIN 200V 0.93typ (Io=100%)
INRUSH CURRENT[A]
ACIN 100V
ACIN 200V
15typ (Io=100%) (At cold start) (Ta=25C)
30typ (Io=100%) (At cold start) (Ta=25C)
LEAKAGE CURRENT[mA]
0.75max (60Hz, According to IEC60950 and DEN-AN)
VOLTAGE[V]
+24
+36
+48
CURRENT[A]
*2 0 - 4.2 (Peak 7)
0 - 2.8 (Peak 4.7)
0 - 2.1 (Peak 3.5)
WATTAGE[W]
100.8 (Peak 168)
100.8 (Peak 169.2)
100.8 (Peak 168)
LINE REGULATION[mV]
48max
48max
48max
LOAD REGULATION[mV]
76max
90max
150max
RIPPLE[mVp-p]
0 to +50C*3 120max
-10 - 0C*3 160max
120max
160max
150max
300max
OUTPUT
RIPPLE NOISE[mVp-p] ^{0 to +50C*3 150max}
-10 - 0C*3 180max
150max
180max
250max
350max
TEMPERATURE REGULATION[mV]
0 to +50C
-10 to +50C
120max
145max
150max
180max
240max
300max
DRIFT[mV]
*4 48max
48max
48max
START-UP TIME[ms]
500max (ACIN 100V, Io=100%)
HOLD-UP TIME[ms]
20typ (ACIN 100V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 21.4 - 26.4
26.4 - 39.6
39.6 - 52.8
OUTPUT VOLTAGE SETTING[V] 23.0 - 25.0
35.0 - 37.0
46.0 - 50.0
PROTECTION ^{OVERCURRENT PROTECTION Works over 101% of peak current and recovers automatically}
CIRCUIT AND OVERVOLTAGE PROTECTION Works at 115 - 140% of rating
OTHERS
REMOTE ON/OFF
Option (Refer to Instruction Manual)
INPUT-OUTPUT -RC
*5 AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
ISOLATION
INPUT-FG
OUTPUT-RC-FG
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
*5 AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature)
OUTPUT-RC
*5 AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature)
OPERATING TEMP.,HUMID.AND ALTITUDE -10 to +70C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max
ENVIRONMENT
STORAGE TEMP.,HUMID.AND ALTITUDE
VIBRATION
-20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max
10 - 55Hz, 19.6m/s² (2G), 3minutes period, 60minutes each along X, Y and Z axis
IMPACT
196.1m/s² (20G), 11ms, once each X, Y and Z axis
SAFETY AND ^{AGENCY APPROVALS}
NOISE
CONDUCTED NOISE
REGULATIONS _{HARMONIC ATTENUATOR}
UL60950-1, C-UL(CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input)
Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B
Complies with IEC61000-3-2 *⁷
OTHERS
CASE SIZE/WEIGHT
COOLING METHOD
75X35X222mm [2.95X1.38X8.74 inches] (WXHXD) /380g max (without chassis and cover)
Convection
*1 Specification is changed at option, refer to Instruction Manual 6.
*2 Peak loading for 10sec. And Duty 35% max, refer to Instruction Manual 5. In detail.
*3 This is the value that measured on measuring board with capacitor of 22mF within 150mm
from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to
KEISOKU-GIKEN: RM101).
*4 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C,
with the input voltage held constant at the rated input/output.
*5 Applicable when remote control (optional) is added.
*6 Please contact us about safety approvals for the model with option.
*7 Please contact us about class C.
* Parallel operation with other model is not possible.
* Derating is required when operated with chassis and cover.
* A sound may occur from power supply at peak loading.
LEP-2