TCT_P Datasheet, PDF (5/7 Pages) Rohm – Chip tantalum capacitors

Tantalum capacitors
Item
Adhesiveness
Performance
The terminal should not come off.
TCT Series P Case
Test conditions (JIS C 5101−1 and JIS C 5101− 3)
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown in the figure
below for 10±1s after mounting the terminal on a circuit board.
product
Apply force
Dimensions
Refer to "External dimensions"
a circuit board
Measure using a caliper of JIS B 7507 Class 2
or higher grade.
Resistance to solvents The indication should be clear
As per 4.32 JIS C 5101-1
As per 4.18 JIS C 5101-3
Dip in the isopropyl alcohol for 30±5s, at room
temperature.
Solderability
3/4 or more surface area of the solder coated
terminal dipped in the soldering bath should
be covered with the new solder.
As per 4.15.2 JIS C 5101-1
As per 4.7 JIS C 5101-3
Dip speed=25±2.5mm / s
Pre−treatment(accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp. : 245±5°C
Duration : 3±0.5s
Solder
: M705
Flux
: Rosin 25% IPA 75%
Vibration
Capacitance Measure value should not fluctuate during the
measurement.
Appearance There should be no significant abnormality.
As per 4.17 JIS C 5101-1
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print circuit board.
z Standard products list, TCT series P case
Part No.
Rated
voltage
85°C
Category
voltage
125°C
Surge
voltage
85°C
(V)
(V)
(V)
TCT P 0E 107M8R 2.5
1.6
3.2
TCT P 0G 107M8R
4
2.5
5.2
TCT P 0G 336M8R
4
2.5
5.2
TCT P 0G 476M8R
4
2.5
5.2
TCT P 0G 686M8R
4
2.5
5.2
TCT P 0J 226M8R 6.3
4
8
TCT P 0J 336M8R 6.3
4
8
TCT P 0J 476M8R 6.3
4
8
TCT P 1A 156M8R 10
6.3
13
TCT P 1A 226M8R 10
6.3
13
TCT P 1A 336M8R 10
6.3
13
TCT P 1C 106M8R 16
10
20
TCT P 1E 225M8R 25
16
33
Cap.
120Hz
(µF)
Leakage
Tolerance current
25°C
Df
120Hz
(%)
Impedance
100kHz
(%) 1WV.60s
25°C
(µA)
−55°C
125°C
85°C
(Ω)
100
±20
12.5
60 30 40
4.0
100
±20
20
60 30 40
4.0
33
±20
1.3
30 20 30
4.0
47
±20
1.9
30 20 30
4.0
68
±20
13.6
60 30 40
4.0
22
±20
1.4
30 20 30
5.0
33
±20
2.1
30 20 30
4.0
47
±20
14.8
60 30 40
4.0
15
±20
1.5
30 20 30
6.0
22
±20
2.2
30 20 30
5.0
33
±20
16.5
60 30 40
4.0
10
±20
1.6
30 20 30
6.0
2.2
±20
0.55
30 20 30
8.0
Rev.D
5/6