TC_A Datasheet, PDF (4/12 Pages) Rohm – Chip tantalum capacitors

Tantalum capacitors
TC Series A Case
Item
Temperature
Stability
Temp.
ΔC / C
Performance
−55°C
Within 0/−12% of initial value
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
Df (tan δ)
Shall be satisfied the voltage on " Standard list "
L.C.
−
Temp.
ΔC / C
Df (tan δ)
+85°C
TCA0G686
TCA0G107
TCA0J686
Others
: Within +12/0% of initial value
: Within +12/0% of initial value
: Within +12/0% of initial value
: Within +10/0% of initial value
Shall be satisfied the voltage on " Standard list "
L.C.
5μA or 0.1CV whichever is greater
Temp.
+125°C
ΔC / C
Within +15/0% of initial value
Df (tan δ)
Shall be satisfied the voltage on " Standard list "
L.C.
6.3μA or 0.125CV whichever is greater
Surge voltage
Appearance
L.C.
ΔC / C
Df (tan δ)
There should be no significant abnormality. As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Shall be satisfied the voltage on " Standard list " _{Apply the specified surge voltage every 5±0.5 min.}
TCA0G686
TCA0G107
TCA0J686
Others
: Within ±15% of initial value
: Within ±20% of initial value
: Within ±20% of initial value
: ±10% of initial value
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Less than initial limit
Loading at
Appearance
High temperature
L.C.
There should be no significant abnormality.
TCA0G686
TCA0G107
TCA1E105
TCA1A226
TCA0J686
Others
: Less than 125% of initial limit
: Less than 125% of initial limit
: Less than 125% of initial limit
: Less than 125% of initial limit
: Less than 125% of initial limit
: Less than initial limit
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 2000+72/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85±2°C, leave the sample at room
temperature / humidity for over 24h and measure the value.
ΔC / C
TCA0G686
TCA0G107
TCA1A226
TCA0J476
TCA0J686
Others
: Within ±15% of initial value
: Within ±20% of initial value
: Within ±15% of initial value
: Within ±15% of initial value
: Within ±20% of initial value
: ±10% of initial value
Df (tan δ) Less than initial limit
Terminal
strength
Capacitance The measured value should be stable.
Appearance There should be no significant abnormality.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
20
50
(Unit : mm)
F (Apply force)
R230
1
thickness=1.6mm
45 45
Rev.D
4/11