|
BD9422EFV_15 Datasheet, PDF (15/30 Pages) Rohm – White LED Driver for large LCD panel | |||
|
◁ |
BD9422EFV
â3.4 Connecting operation of Master/ slave
Master IC
SUMPWM
100k
SUMPWMDET
+
-
CS
Master:Low
RCS
Slave :High
MSDET
+
-
3V
Datasheet
PWM1
ï½
PWM6
A5V
+
-
ERRAMP
100k
FB
Master:ON
Slave :OFF
Recognized slave mode
ã¹ã¬ã¼ãã¢ã¼ãèªè
ââ
ã¨Cã©uã¼r ã¢erã³rãorã·aã³mã¯på´sã«inããk side
ããã¹ã¤Rã¿aeã¼ncã¢odgã¼enãvièªezneèdomneasotfesrlmavoedâse
ã¹ã¬ã¼ãå´ã®ã¿PWM on
ã©ãã1ã¤ã§ãPWMãâON
âãã«ã¢Aãdãdä»på ull-up resistance
Recognized master mode
ãã¹aã¿nã¼dã¢aã¼llãPèªWèM off in Master
ãã¤
and Slave
ãã¹ã¿ã¼/ã¹ã¬ã¼ãå
¨âã¦ã§
PWM
â
OFF
Cut
FB
output
FBåºåカッï¾
ã¹ã¬Rã¼eãcã¢oã¼gnãiï¾èªzeèd slave mode
ãã¤and all PWM off in Slave
ã¹ã¬ã¼ãã®PWMãå
¨ã¦OFF
â
â
FBåºåã«ãCãut FB output
Slave IC
SUMPWM
CS
FB
Figure 19.
Connecting plural BD9422EFVs makes it a Master/slave, a DCDC in Master construct a system to drive LED driver. Here,
explanation of Master/slave operation in connecting 2 ICs.
[MSDET] Convertor for recognizing Master/slave
Detect the voltage of CS terminal to judge master or slave of itself. The CS terminal of slave is OPEN when the
Master/slave mode is used. The CS terminal is high due to being supplied constant current from IC inside. The CS terminal
of Master is connected a resistance for DCDC switching current detection and swing 0V to 0.45V on operating. Convertor
can detect the differences of the voltage, which is a Master/slave recognizing signal.
[SUMPWMDET] Converter for all PWM signal detection
SUMPWM terminal is connected a switch that is ON when the PWM signal is high and a pull down resistance 100kâ¦.
SUMPWM terminal becomes high more than one PWM signals are high.
When the SUMPWM terminal is connected between master and slave, it can judge if more than one signals of the entire
PWM signal in master/slave becomes high.
The operation of error amplifier part is decided by the signal of MSDET and SUMPWM
1.Error amplifier output part Diode/non diode
If the IC recognizes slave mode, the diode is connected to error amplifier output and cut the supply of sink side of error
amplifier.
2.Error amplifier output part Pull up resistance/ non pull up resistance
If the IC recognizes master mode and the PWM of slave become ON more than one, the pull up resistance is connected.
3. Error amplifier output FB output cut
In master recognizing, if all the PWM signals are OFF error amplifier output is cut.
In slave recognizing, if all the PWM signals of slave side are OFF error amplifier output is cut.
These are collected, the table below.
Use for Masterï¼Slave mode
Master Slave
Master
Error Amplifier output
source
sink
pull up
PWM ON PWN ON â
â
ï¼
PWM ON PWM OFF â
â
ï¼
PWM OFF PWM ON â
â
â
PWM OFF PWM OFF ï¼
ï¼
ï¼
Slave
Error Amplifier output
source
sink
pull up
â
ï¼
ï¼
ï¼
ï¼
ï¼
â
ï¼
ï¼
ï¼
ï¼
ï¼
Use for Master only
Master
PWM ON
PWM OFF
Master
Error Amplifier output
source
sink
pull up
â
â
ï¼
ï¼
ï¼
ï¼
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111ã»15ã»001
15/26
TSZ02201-0F1F0C100210-1-2
1.Sep.2015 Rev.006
|
▷ |