SMLP36 Datasheet, PDF (1/2 Pages) Rohm – Tri-Color Top View 0604 <1.5 1.0 t=0.2mm> High Brightness Type

Tri-Color Top View
0604 <1.5 1.0 t=0.2mm> High Brightness Type
SMLP36 Series (under development)
PICOLED^TM -RGB
Target Spec.
Emitting Color
Material
Package Size(mm)
Part No.
SMLP36RGB1W
Blue
InGaN on SiC
Green
Red
AlGalnP on GaAs
1510(0604) 1.5×1.0(t=0.2)
Absolute Maximum Ratings (Ta=25°C)
Part No.
Emitting
color
Power ^Forward
dissipation ^current
PD
(mW)
IF
(mA)^∗1
Peak
forward
current
IFP
(mA)^∗2
Reverse Operating Storage
voltage temperature temperature
VR
Topr
Tstg
(V)
(°C)
(°C)
Blue
SMLP36
Green
64
20
100
5
-30 to +85 -40 to +100
Red
1:The above absolute maximum ratings are valid for the case of lighting a single color. When lighting two colors at
the same time, each of the figures in the absolute maximum ratings should be reduced down to 50% of it. When
lighting three colors, it will be reduced down to 30% of it. (DC drive)
2:Conditions of IFP : Pulse width 1ms Duty 1/120
Electrical Optical Characteristics (Ta=25°C)
Part No.
Resin Color
Forward
voltage
VF
Typ. IF
(V) (mA)
3.0
(3.2)
SMLP36
Milkey 3.1
5
White (3.3) (20)
1.9
(2.2)
3:Measurement tolerance : ±2nm
Reverse
current
IR
Max. VR
(µA) (V)
100 5
Light wavelength
Dominant
λD^∗3
Typ. IF
(nm) (mA)
Brightness
IV
Min. Typ. IF
(mcd) (mcd) (mA)
9.0 18
470
(28) (50)
36 71
5
527 5
(110) (200) (20)
14 28
624
(56) (100)
Dimensions (Unit:mm)
1.5
R
B
G
1.42
0.9
0.4
Anode
B RG
Tolerance: ± 0.1
Cathode
Directivity (Typ.)
X
Y
Green
Red
Green
30
Angular Displacement (deg)
0
Red
30
60 _{In preparation} 60
90
100
50
0
50
RELATIVE LUMINOUS INTENSITY (%)
90
100
Red
X’
Y’
Green
Angular Displacement (deg)
0
30
30
Green, Red
60 _{In preparation} 60
90
100
50
0
50
RELATIVE LUMINOUS INTENSITY (%)
90
100
Recommended Pad Layout
0.45
0.4
0.4
Packaging Specifications (Unit:mm)
Tape Specifications:1 <5,000pcs/reel>
4.0± 0.1
2.0± 0.05
Feeding direction
φ
1.5
+0.1
0
0.20±0.08
Reel Specifications
11.4±1
0.25
0.25 _(Unit:mm)
The recommended thickness of the screen mask
4.0±0.05
1.62
for soldering is between 80 and 130µm. The hole
size of the screen mask should be same as the
0.28±0.05
recommended land pattern or smaller.
Tolerance: ± 0.2
Tolerance: ± 0.2