BP5710-1_10 Datasheet, PDF (1/4 Pages) Rohm – Isolated AC/DC Converter

Data Sheet
100VAC Input/12VDC (350mA) Output
Isolated AC/DC Converter
BP5710-1
Absolute Maximum Ratings
Parameter
Symbol
Input voltage
Vi
Output current
Io
ESD endurance
Vsurge
Operating temperature range Topr
Storage temperature range Tstg
Voltage between 1&2 order BV
Limits
170
350
2
−20 to +80
−25 to +105
1800
Unit
V
mApk
kV
°C
°C
Vrms
Conditions
DC
IEC61000-4-2 Highest level 1
2s
Electrical Characteristics
Parameter
Symbol Min. Typ. Max. Unit
Conditions
Input voltage range
Vi 120 141 162 V DC(85 to 115VAC)
Output voltage
Vo 11.0 12.0 13.0 V Vi=141V, Io=350mA
Output current
Io
Line regulation
Vr
Load regulation
Vl
Output ripple voltage Vp
Power conversion efficiency η
Isolation resistance
BR
0
−
350 mA Vi=141V
∗1
− 0.15 0.3
V Vi=120 to 162V, Io=350mA
− 0.15 0.3
V Vi=141V, Io=0 to 350mA ^∗2
− 0.25 − Vp-p Vi=141V, Io=350mA
70 77
−
% Vi=141V, Io=350mA ^∗2
100 −
−
MΩ DC100V between 1&2 order
∗1 The max Output current is changed due to the ambient temperature. Please refer to the note regarding derating curve.
∗2 Please refer to regarding the definitions of the Load regulation, Conversion efficiency.
Application Circuit
BP5710-1
Be sure to use fuse for safety.
12
45
Input
AC100V
50Hz/60Hz
FL1 D1 ^FUSE
+
−
8 10 11
Output
12V
+
−
Pin No.
Function
1 Input terminal Vi(141VDC)
2 Input terminal Vi(141VDC)
3 Not used
4 COMMON (Primary)
5 COMMON (Primary)
6 Not used
7 Not used
8 COMMON (Secondary)
9 Not used
10 Capacitor connect
11 Output terminal Vo(12V)
ZNR C1 C2 C3
C4
C5
Please verify operation and characteristics in the customer's circuit before actual usage.
Ensure that the load current does not exceed the maximum rating.
External Component Specifications
FUSE : Use a quick-acting fuse of 0.5A.
ZNR : Varistor
D1: Rectifier diode
C3: Input smoothing
capacitor
A varistor is required to protect against lightning surges and static electricity.
In the absolute maximum ratings, the reverse peak voltage should be
400V or higher, the average rectifying current should be 0.5A or higher,
and the peak surge current should be 20A or higher.
(Full-wave rectification can be used.)
Rated voltage : 200V or higher. Capacitance : 33 to 330µF
FL1: Noise reduction filter Use a line filter if necessary.
C1,2,4 : Noise reduction
capacitors
Capacitance (C1,C2) : 0.1 to 0.22µF, (C4) : 4700pF
Rated voltage : 200V or higher. Film or ceramic capacitor.
Evaluate under actual operating conditions.
C5: Output smoothing
capacitor
Capacitance : 470 to 1000µF Rated voltage : 25V or higher,
ESR is 0.16Ω max. Ripple current is 0.58Arms or greater
Low impedance type.
Evaluate under actual operating conditions.
www.rohm.com
©2010 ROHM Co., Ltd. All rights reserved.
1/1
Dimensions (Unit : mm)
36.0MAX.
15.0MAX.
12 45
8
0 . 5 ±0 . 1
P= 2.54±0.2
1 . 3 ±0 . 2
5.5MAX
2.54�10=25.4
10 11
0 . 2 5 ±0 . 0 5
5.25MAX.
9.75MAX.
Derating Curve
Derating Curve
400
350
300
250
200
Operation Range
150
100
50
0
-30 -20 -10 0 10 20 30 40 50 60 70 80 90
Ambient Temperature Ta(°C)
Switching Frequency
600
500
400
300
200
100
0
0
Switching Frequency
(Ta=25°C, Vi=141V)
50 100 150 200 250 300 350
Output Current Io(mA)
Conversion Efficiency
100
90
80
70
60
50
40
30
20
10
0
0
Conversion Efficiency
(Ta=25°C, Vi=141V)
50 100 150 200 250 300 350
Output Current Io(mA)
Load Regulation
Load Regulation
(Ta=25°C, Vi=141V)
14
12
10
8
6
4
2
0
0 100 200 300 400 500 600 700
Output Current Io(mA)
Surface Temperature Increase
Surface Temperature Increase
(Ta=25°C, Vi=141V)
60
50
40
30
20
10
0
0 50 100 150 200 250 300 350
Output Current Io(mA)
2010.01 - Rev.A