RI-07AAA Datasheet, PDF (2/2 Pages) RHOPOINT COMPONENTS – SPST

RI-07 Series
Model Number
Parameters
Test Conditions
Operating Characteristics
Operate Range
Release Range
Operate Time - including bounce (typ.)
Bounce Time (typ.)
Release Time (max)
Resonant Frequency (typ.)
Electrical Characteristics
Switched Power (max)
Switched Voltage DC (max)
Switched Voltage AC, RMS value (max)
Switched Current DC (max)
Switched Current AC, RMS value (max)
Carry Current DC (max)
Breakdown Voltage (min)
Contact Resistance (initial max)
Contact Resistance (initial typ.)
Contact Capacitance (max)
Insulation Resistance (min)
(energization)
(energization)
without test coil
RH £ 45%
Units
AT
AT
ms
ms
ms
Hz
W
V
V
mA
mA
A
V
mW
mW
pF
MW
RI-07AAA
RI-07AA
RI-07A
7-19
3-16
0.25 (24 AT)
0.05 (24 AT)
30 (24 AT)
6700
16-25
4-18
0.25 (31 AT)
0.05 (31 AT)
30 (31 AT)
6700
20-36
6-19.5
0.45 (45 AT)
0.05 (45 AT)
30 (45 AT)
6700
5
160
110
250
250
1.5
180
130 (20 AT)
110 (20 AT)
0.3
10⁶
10
200
140
500
500
1.75
250
130 (25 AT)
110 (25 AT)
0.3
10⁶
10
200
140
750
750
1.75
280
130 (25 AT)
110 (25 AT)
0.25
10⁶
MECHANICAL DATA
Contact arrangement is normally open; lead finish is tinned;
net mass is approximately 0.10 g; and can be mounted in any
position.
SHOCK
The switches are tested in accordance with “IEC 68-2-27”, test
Ea (peak acceleration 150 G, half sinewave; duration 11 ms).
Such a shock will not cause an open switch (no magnetic field
present) to close, nor a switch kept closed by an 80 AT coil to
open.
VIBRATION
The switches are tested in accordance with “IEC 68-2-6”, test
Fc (acceleration 10 G; below cross-over frequency 57 to 62
Hz; amplitude 0.75 mm; frequency range 10 to 2000 Hz,
duration 90 minutes). Such a vibration will not cause an open
switch (no magnetic field present) to close, nor a switch kept
closed by an 80 AT coil to open.
MECHANICAL STRENGTH
The robustness of the terminations is tested in accordance with
“IEC 68-2-21”, test Ua₁ (load 10 N).
OPERATING AND STORAGETEMPERATURE
Operating ambient temperature; min: -55°C; max: +125°C.
Storage temperature; min: -55°C; max: +125°C.
Note: Temperature excursions up to 150°C may be permissible.
For more information contact your nearest Coto Technology
sales office.
SOLDERING
The switch can withstand soldering heat in accordance with
“IEC 68-2-20”, test Tb, method 1B: solder bath at 350 ±10° C
for 3.5 ±0.5 s.
Solderability is tested in accordance with “IEC 68-2-20” test
Ta, method 3: solder globule temperature 235°C; ageing 1b:
4 hours steam.
WELDING
The leads can be welded
MOUNTING
The leads should not be bent closer than 1 mm to the glass-to-
metal seals. Stress on the seals should be avoided. Care must
be taken to prevent stray magnetic fields from influencing the
operating and measuring conditions.
Rhopoint Components Ltd Fax: [phone] Phone: [phone] web: www.rhopointcomponents.com e-mail: [e-mail]