RFPA2002 Datasheet, PDF (4/12 Pages) RF Micro Devices – Integrated Power Amplifier 1750MHz to 2200MHz

RFPA2002
Parameter
Band 1 (4) Downlink
Electrical Specifications
Gain
ACLR 1
ACLR 2
PA Efficiency (PAE)
PA Current Drain
Noise Figure
Input Impedance
IM3
IM5
Harmonics 2f0
Harmonics 3f0
Enable Current
Mode Current
DC Enable Time
RF Rise/Fall Time
Coupling Factor
Coupling Accuracy – Temp /
Voltage
Coupling Accuracy – VSWR
Output Load VSWR Stability
(Spurious Emissions)
Specification
Unit
Min Typ Max
Condition
Unless Otherwise Specified: Temp = 25°C, VBATT = +3.3V,
VEN = +1.8V, Freq = 2150MHz, 50Ω, 20MHz
LTE DL with 7.5dB CFR
23.5 26.5 29.5 dB High Power Mode (HPM), P_OUT = 24dBm, V_CC = 3.3V
20 22.5 26
dB Medium Power Mode (MPM), P_OUT = 14dBm, V_CC = 1.4V
12 15.3 18
dB Low Power Mode (LPM), P_OUT = 3dBm, V_CC = 0.8V
-32
dBc HPM, P_OUT = 24dBm, V_CC = 3.3V, without DPD
-50
dBc HPM, P_OUT = 24dBm, V_CC = 3.3V, with DPD
-45
dBc HPM, P_OUT = 24dBm, V_CC = 3.3V, without DPD
-54
dBc HPM, P_OUT = 24dBm, V_CC = 3.3V, with DPD
23
%
HPM, POUT = 24dBm, VCC = 3.3V
329
mA _{HPM, POUT = 24dBm, VCC = 3.3V}
3.5
dB
1.4:1 2:1 VSWR _{No external matching, POUT ≤ 24dBm, all modes}
-15
dBm _{Two tones passed 600kHz, HPM, Total POUT ≤ 24dBm, VCC = 3.3V}
-20
dBm _{Two tones passed 600kHz, HPM, Total POUT ≤ 24dBm, VCC = 3.3V}
-8
dBm _{CW POUT ≤ 24dBm, all power modes}
-26
dBm _{CW POUT ≤ 24dBm, all power modes}
0.1
mA _{Sources or sink current, VEN = 1.8V}
0.1
mA _{Source or sink current, VMODE0, VMODE1 = 1.8V}
10
µs
DC only; Time from VEN = high to stable idle current (90% of steady state
value)
10
µs _{POUT ≤ 24dBm, all modes, 90% of target, DC settled prior to RF}
16 19 22
dB _{POUT ≤ 24dBm, all modes}
-0.5
0.5
dB
POUT ≤ 24dBm, all modes 30°C ≤ T ≤ 85°C , VCC as required, referenced to
25°C, 3.3V conditions
-0.8
0.8
dB P_OUT ≤ 24dBm, all modes, load VSWR = 2.5:1
-60 dBc P_OUT ≤ 24dBm, all conditions, load VSWR = 8:1, all phase angles
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
DS150209
For sales or technical support, contact RFMD at +1.336.678.5570 or [e-mail].
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
4 of 12