RFFM6406 Datasheet, PDF (3/8 Pages) RF Micro Devices – 2.5V to 4.2V, ISM Band, 1 1/2W, 408MHz to 455MHz Transmit/Receive Module

DRAFT
RFFM6406
DRAFT
RFMD + TriQuint = Qorvo
Parameter
Transmit High Power Mode
Nominal Power
Saturated Power
Input Return Loss
Output Return Loss Small Signal
Operating Current
Worst-Case Operating Current,
6:1 VSWR
Quiescent Current
IDD
IAPC
Second Harmonic
Third - Tenth Harmonic
Gain
Output Power Variation
Module PAE
PA PAE
Power on RX Port (Pin 18)
Transmit Bypass Mode
Insertion Loss
Input P1dB
Input IP3
Input Return Loss
Output Return Loss
Second Harmonic Attenuation
Third - Tenth Harmonic Attenuation
Receive Mode
IP1dB
Gain
Operating Current
IDD
Noise Figure
IIP3
Specification
Min Typ Max
30.0 31.0 31.5
30.0 31.0 31.5
30.0 31.0 31.5
32.0 32.5
32.0 32.5
31.5 32.2
12
7
770 1000
1200
80
35
15
30 60
-30
-60
25.0
22.0
-0.4
-0.4
40
62
-20
2.5 3.0
26 30
43 45
15
15
30
50
-12
14 15 16
4
5
7
1
1.9 2.7
1
3
5
Unit
dBm
dBm
dBm
dBm
dBm
dBm
dB
dB
mA
mA
mA
µA
mA
µA
dBc
dBc
dB
dB
dB
%
%
dBm
dB
dBm
dBm
dB
dB
dB
dB
dBm
dB
mA
mA
dB
dBm
Condition
VCCTx1 = 3.9V, VCCTx2 = 3.9V, VDD = 3.9V,
VAPC = 2.3V, EN = 1.8V, TR = 1.8V, BYP = 0.2V,
Measured Path=TX to ANT, Temperature = 25ºC
PIN = +3.5dBm, Temp = 25ºC
PIN = +1.5dBm, Temp = -30ºC
PIN = +4.5dBm, Temp = 60ºC
PIN = +10.0dBm, Temp = 25ºC
PIN = +10.0dBm, Temp = -30ºC
PIN = +10.0dBm, Temp = 60ºC
POUT = 31.0dBm, ICC TX1 + ICC TX2
ICC TX1 + ICC TX2, Over Temperature, at nominal power input drive
ICC TX1 + ICC TX2, RF = Off
I APC, RF = Off
POUT = 31.0dBm
POUT = 31.0dBm
POUT = 31.0dBm, FO= 408MHz to 455MHz
POUT = 31.0dBm
VCCTx1, VCCTx2 = 3.9V, PIN = +6dBm
VCCTx1, VCCTx2= 2.7V, PIN = +6dBm
Over frequencies and voltage
VCCTx1, VCCTx2 = 3.9V, POUT = 31dBm (takes into account filter and switches)
VCCTx1, VCCTx2 = 3.9V, POUT = 31dBm (Excludes losses of module filter and
switches)
POUT = 31.0dBm
VCCTx1 = 3.9V, VCCTx2 = 3.9V, VDD = 3.9V,
VAPC = 0.0V, EN = 1.8V, TR = 1.8V, BYP = 1.8V,
Measured Path=TX to ANT, Temperature = 25ºC
Second Harmonic Insertion Loss
Third-Tenth Harmonic Insertion Loss
VCCTx1 = 3.3V, VCCTx2 = 3.3V, VDD = 3.3V, VCCRx = 3.3V,
VAPC = 0.0V, EN = 1.8V, TR = 0.2V, BYP = 0.2V,
Measured Path = SAW2 to RX, Temperature = 25ºC
Revision DS20150708
DRAFT ^{© 2015 RF Micro Devices, Inc.}
3 of 8
Disclaimer: Subject to change without notice
DRAFT ^{www.rfmd.com / www.qorvo.com}