RX5001 Datasheet, PDF (4/10 Pages) RF Monolithics, Inc – 315.00 MHz Hybrid Receiver

ASH Receiver Theory of Operation
Introduction
RFM’s RX5000 series amplifier-sequenced hybrid (ASH) receivers are
specifically designed for short-range wireless control and data communica-
tion applications. The receivers provide robust operation, very small size,
low power consumption and low implementation cost. All critical RF func-
tions are contained in the hybrid, simplifying and speeding design-in. The
ASH receiver can be readily configured to support a wide range of data
rates and protocol requirements. The receiver features virtually no RF
emissions, making it easy to certify to short-range (unlicensed) radio regu-
lations.
Amplifier-Sequenced Receiver Operation
The ASH receiver’s unique feature set is made possible by its system ar-
chitecture. The heart of the receiver is the amplifier- sequenced receiver
section, which provides more than 100 dB of stable RF and detector gain
without any special shielding or decoupling provisions. Stability is achieved
by distributing the total RF gain over time. This is in contrast to a superhet-
erodyne receiver, which achieves stability by distributing total RF gain over
multiple frequencies.
Figure 1 shows the basic block diagram and timing cycle for an amplifier-
sequenced receiver. Note that the bias to RF amplifiers RFA1 and RFA2
are independently controlled by a pulse generator, and that the two ampli-
fiers are coupled by a surface acoustic wave (SAW) delay line, which has
a typical delay of 0.5 µs.
An incoming RF signal is first filtered by a narrow-band SAW filter, and is
then applied to RFA1. The pulse generator turns RFA1 ON for 0.5 µs. The
amplified signal from RFA1 emerges from the SAW delay line at the input
to RFA2. RFA1 is now switched OFF and RFA2 is switched ON for 0.55 µs,
amplifying the RF signal further. The ON time for RFA2 is usually set at 1.1
times the ON time for RFA1, as the filtering effect of the SAW delay line
stretches the signal pulse from RFA1 somewhat. As shown in the timing di-
agram, RFA1 and RFA2 are never on at the same time, assuring excellent
receiver stability. Note that the narrow-band SAW filter eliminates sampling
sideband responses outside of the receiver passband, and the SAW filter
and delay line act together to provide very high receiver ultimate rejection.
Amplifier-sequenced receiver operation has several interesting character-
istics that can be exploited in system design. The RF amplifiers in an am-
plifier-sequenced receiver can be turned on and off almost instantly,
allowing for very quick power-down (sleep) and wake-up times. Also, both
RF amplifiers can be off between ON sequences to trade-off receiver noise
figure for lower average current consumption. The effect on noise figure
can be modeled as if RFA1 is on continuously, with an attenuator placed in
front of it with a loss equivalent to 10*log₁₀(RFA1 duty factor), where the
duty factor is the average amount of time RFA1 is ON (up to 50%). Since
an amplifier-sequenced receiver is inherently a sampling receiver, the
overall cycle time between the start of one RFA1 ON sequence and the
start of the next RFA1 ON sequence should be set to sample the narrowest
RF data pulse at least 10 times. Otherwise, significant edge jitter will be
added to the detected data pulse.
ASH Receiver Block Diagram & Timing Cycle
Antenna
SAW Filter
RFA1
P1
SAW
Delay Line
Pulse
Generator
RFA2
Detector &
Low-Pass
Filter
Data
Out
P2
RF Input
t_PW1
P1
RFA1 Out
t_PRI
t_PRC
Delay Line
Out
t_PW2
P2
RF Data Pulse
Figure 1
RF Monolithics, Inc. Phone: [phone]
Fax: [phone]
RFM Europe
Phone: [phone]
Fax: [phone]
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: [e-mail]
http://www.rfm.com
RX5001-062805
Page 4 of 10