SF2293E Datasheet, PDF (1/5 Pages) RF Monolithics, Inc – 1561 MHz SAW Filter

• Low Loss RF SAW Filter
• Surface Mount 3.0 x 3.0 mm Package
• Complies with Directive 2002/95/EC (RoHS) _Pb
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Suitable for Lead-free Soldering - Maximum Soldering Profile
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 1550.5 to 1571.5 MHz
Amplitude Ripple, 1550.5 to 1571.5 MHz
Input/Output VSWR, 1550.5 to 1571.5 MHz
Attenuation, Referenced to 0 dB:
f_C - 500 to f_C - 100 MHz
f_C - 100 to f_C - 60 MHz
f_C - 60 to f_C - 40 MHz
f_C + 40 to f_C + 60 MHz
f_C + 60 to f_C + 80 MHz
f_C + 80 to f_C + 500 MHz
Source Impedance
Load Impedance
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 Inch
Reel Size 13 Inch
Electrical Connections
Connection
Terminals
Input
2
Output
5
Case Ground
All others
SF2293E
Value
Units
10
dBm
3
V
-40 to +70
°C
-40 to +85
°C
260°C for 30 s
1561 MHz
SAW Filter
Sym Notes
Min
f_C
IL
Typ
1561
3.3
0.5
1.5:1
SM3030-6
Max
4.0
2.0
2:1
Units
MHz
dB
45
49
40
45
20
32.5
dB
20
26
35
43
45
50
Z_S
50

Z_L
50
SM3030-6 3.0 x 3.0 mm Nominal Footprint
A45, YWWS
500 Pieces/Reel
3000 Pieces/Reel
50 ohm
2
5
S5 F. 22 9& 3$ E-
1,3,4,6
50 ohm
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50  and measured with 50  network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [e-mail]
© 2011 by RF Monolithics, Inc.
Page 1 of 5
SF2293E - 11/29/11