SF1186B-2 Datasheet, PDF (1/6 Pages) RF Monolithics, Inc – 1575.42 MHz SAW Filter

®
• Designed for Front End GPS Applications
• Low Insertion Loss
• 3.0 x 3.0 x 1.3 mm Surface-Mount Case
• No Matching Circuit Required
• Complies with Directive 2002/95/EC (RoHS) ^Pb
SF1186B-2
1575.42 MHz
SAW Filter
Maximum Ratings at +25°C unless stated otherwise
Rating
Symbol
Maximum Input Signal Level
Withstanding DC Voltage
WVdc
Operating Temperture Range
Storage Temperature Range
Lead Soldering Temperature for 10 Seconds
Peak Reflow Solder Temp for 40 Seconds
T_A
T_STG
T_WAVE
T_Reflow
Suitable for lead-free soldering - Max Soldering Temperature
Value
Units
+10
dBm
4
Volts
-40 to +85
°C
-40 to +105
°C
260
°C
235
°C
260°C for 30 s
SM3030-6
Electrical Characteristics
Center Frequency
Characteristic
1dB Passband width
Pass Band Variation Fc ±2.0 MHz
Pass Band VSWR
Insertion Loss
Absolute Attenuation @
Temperature Coefficient
Operating Temperature
Single Ended Input / Output, Impedance match
Case Style
Lid Symbolization
y=year, ww=week, s=shift
Standard Reel Quantity Reel Size 7 Inch
Reel Size 13 Inch
850 MHz
1500 MHz
1535.42 MHz
1615.42 MHz
1640 MHz
1700 MHz
Sym
f_O
T_A
Notes
Min
Typ
Max
1
1575.42
1
2.046
15.3
0.1
1.0
1.4
2.0
1
2.68
3.5
1
45
51.2
1
40
52.7
1
20
38.9
1
20
58.8
1
45
59.1
1
50
56.7
-30
1
-40
+85
No matching network required for operation at 50 ohms
SM3030-6 3 x 3 mm Nominal Footprint
468 YWWS
500 Pieces/Reel
6
3000 Pieces/Reel
Units
MHz
MHz
dB
dB
dB
ppm/°C
°C
Electrical Connections
Pin #
1
2
3
Description
Ground
Input
Ground
Pin #
4
5
6
Description
Ground
Output
Ground
Notes:
1. Unless noted otherwise, all specifications apply over the operating
temperature range with filter soldered to the specified demonstration
board without impedance matching and measured with 50 Ω network
analyzer.
2. The design, manufacturing process, and specifications of this filter
are subject to change.
3. Either Port 1 or Port 2 may be used for either input or output in the
design. However, impedances and impedance matching may vary
between Port 1 and Port 2, so that the filter must always be installed
in one direction per the circuit design.
4. US and international patents may apply.
5. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered
trademarks of RF Monolithics, Inc.
6. Tape and Reel Standard Per ANSI / EIA 481.
7. ©Copyright 1999, RF Monolithics Inc.
8. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc. Phone: [phone]
Fax: [phone]
RFM Europe
Phone: [phone]
Fax: [phone]
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: [e-mail]
http://www.rfm.com
SF1186B-2-121604
Page 1 of 6