HA17903A Datasheet, PDF (4/9 Pages) Renesas Technology Corp – Dual Comparators

HA17903A Series
Absolute Maximum Ratings
(Ta = 25°C)
Item
Symbol
Ratings
Unit
Power supply voltage
Differential input voltage
Input voltage
Output pin voltage
Output short current
Allowable power dissipation
DIP
SOP
TSSOP
V_CC
Vin(diff)
Vin
Vout
Ios *¹
P_T
36
V
±V_CC
V
−0.3 to +V_CC
V
−0.3 to +36
V
constant
570 *²
mW
385 *³
192 *⁴
Operating temperature
Topr
−40 to +85
°C
Storage temperature
Tstg
−55 to +125
°C
Notes: 1. Short circuit between the output and V_CC will be a cause to destory the circuit. The maximum output current
is about 20 mA for any supply voltage.
2. HA17903APS:
These are the allowable values up to Ta = 55°C. Derate by 8.3mW/°C above that temperature.
3. HA17903AFP/ARP:
These are the allowable values up to Ta = 25°C mounting in air.
When it is mounted on glass epoxy board of 40 mm × 40 mm × 1.5 mmt with 30% wiring density, the
allowable value is 570 mW up to Ta = 45°C. If Ta > 45°C, derate by 7.14 mW/°C.
4. HA17903AT:
These are the allowable values up to Ta = 25°C. Derate by 1.92 mW/°C above that temperature.
Electrical Characteristics
(V_CC = 5 V, Ta = 25°C)
Item
Input offset voltage *¹
Symbol Min Typ Max Unit
V_IO

2
5
mV
Test Conditions
Input offset current
Input bias current *²
Common mode input voltage *³
I_IO
I_IB
V_CM+
V_CM^−

3
50
nA
 I_{IN (+)} − I_{IN (−)} 

25
250
nA
I_{IN (+)} or I_{IN (−)}
3.5


V


0
V
Supply current
I_CC
Voltage gain *⁵
A_VD
Response time *^4,5
t_R
Large signal response time *⁵ t_RI

0.8 2.0 mA All comparators: R_L = ∞, All channels on
 (200)  V/mV V_CC = 15V, R_L ≥ 15kΩ
 (1.3) 
µs V_RL = 5V, R_L = 5.1kΩ
 (300) 
ns V_IN = TTL Threshold width, V_REF = 1.4V
Output sink current
I_O(sink)
6
16

mA V_{IN (−)} ≥ 1V, V_{IN (+)} = 0, V_O ≤ 1.5V
Output saturation voltage
Output leak current *⁵
V_O(sat)
I_LO


400
mV V_{IN (−)} ≥ 1V, V_{IN (+)} = 0, Iosink = 4mA
 (0.1) 
nA V_{IN (−)} = 0, V_{IN (+)} ≥ 1V, V_O = 5V
Notes: 1. V_REF = 1.4 V and R_S = 50 Ω, when V_O = 1.4 V at output switching point.
2. Under linear operation.
3. Common mode input voltage or each one of the input signal should not be less than −0.3 V.
4. This is a value to 100 mV input step voltage with 5 mV over drive.
5. Design spec.
Rev.1.00 Mar 10, 2006 page 4 of 8