M306V2ME-XXXFP Datasheet, PDF (252/271 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER

M306V2ME-XXXFP, M306V2EEFP
5.3 Electrical Characteristics
Table 5.3.1 Electrical characteristics (referenced to VCC = 5 V, VSS = 0 V at Ta = 25 ^oC, f(XIN) = 10 MHz
unless otherwise specified)
Symbol
HIGH output
VOH
voltage
Parameter
Measuring condition
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P63, P67, P72 to P77 ,
IOH = –5 mA
P82, P83, P86, P87, P90 to P94,
P100 to P107, R, G, B, OUT1,
OUT2
Standard
Min. Typ. Max.
Unit
3.0
V
HIGH output P00 to P07,P10 to P17, P20 to P27,
VOH
voltage
P30 to P37, P40 to P47, P50 to P57 ^{IOH = –200 µA}
4.7
V
VOH
VOL
VOL
VOL
VOL
VT+-VT-
VT+-VT-
VT+-VT-
II H
IIL
RPULLUP
Icc
HIGH output
voltage
XOUT
HIGH POWER
LOW POWER
IOH = –1 mA
IOH = –0.5 mA
3.0
3.0
LOW output
voltage
P00 to P07,P10 to P17,P20 to P27,
P30 to P37,P40 to P47,P50 to P57,
P60 to P63, P73 to P77,
P82, P83, P86, P87, P90 to P92,
P100 to P107, R, G, B, OUT1,
OUT2
IOL = 5 mA
LOW output P67, P70 to P72, P93, P94
voltage
IOL = 6.0 mA
LOW output P00 to P07, P10 to P17, P20 to P27,
voltage
P30 to P37, P40 to P47, P50 to P53 ^{IOL = 200 µA}
LOW output
voltage
XOUT
HIGHPOWER
LOWPOWER
IOL = 1 mA
IOL = 0.5 mA
Hysteresis ^{HOLD, RDY, TB0IN to TB2IN,}
INT0, INT1, CTS0, CTS2,
CLK0, CLK2, SCL1 to SCL3,
0.2
SDA1 to SDA3, HSYNC, VSYNC,
HC0, HC1, RxD0
Hysteresis RESET
0.2
Hysteresis XIN
0.2
HIGH input
current
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P63, P67, P70 to P77,
P82, P83, P86, P87,
P90 to P94,P100 to P107,
XIN, RESET, CNVss, BYTE, OSC1
VI = 5 V
LOW input
current
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P63, P67, P70 to P77,
P82, P83, P86, P87,
P90 to P94,P100 to P107,
XIN, RESET, CNVss, BYTE, OSC1
VI = 0 V
Pull-up resistor
P00 to P07, P10 to P17, P20 to P27,
P30 to P37, P40 to P47, P50 to P57,
P60 to P63, P67, P72 to P77, P82, P83,
P86, P87, P90 to P94, P100 to P107
VI = 0 V
30.0
Power supply current
f(XIN) = 10 MHz _{OSD ON, Data slicer ON}
In single-chip ^{Square wave,}
mode, the
no division
OSD OFF, Data slicer OFF
output pins ^{f(XIN) = 10 MHz OSD OFF, Data slicer OFF}
are open and
other pins are
Square wave,
division by 8
VS S
f(XCIN) = 32kHz
When a WAIT
instruction is
executed
Ta=25 °C when
clock is stopped
Ta = 70 °C when
clock is stopped
V
2.0 V
0.6 V
0.45 V
2.0
V
2.0
0.8 V
1.8 V
0.8 V
5.0 µA
–5.0 µA
50.0 167.0 kΩ
70
90
mA
30
50
10
mA
10
µA
10
µA
200
RBS
I²C-BUS • BUS switch connection resistor _{Vcc = 4.5 V}
(between SCL1 and SCL2, SDA1 and SDA2)
130 Ω
RfXIN
Feedback resistor XIN
1.0
MΩ
RfXCIN
Feedback resistor XCIN
6.0
MΩ
Rev.1.40 Oct 06, 2004 page 252 of 269