TPS-1 Datasheet, PDF (19/39 Pages) Cooper Bussmann, Inc. – Telpower® Fuses 1 to 70 Amps, 170 Volts DC

TPS-1
1. Pin Functions
Pin Name
GPIO_30
GPIO_31
GPIO_32
GPIO_33
GPIO_34
GPIO_35
GPIO_36
GPIO_37
GPIO_38
GPIO_39
GPIO_40
GPIO_41
GPIO_42
GPIO_43
GPIO_44
GPIO_45
GPIO_46
GPIO_47
I/O Input type
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
I/O Schmitt
Output
type
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
3.3V CMOS
Pull
up / down
internal
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Pull
up / down
external
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
see note 2
Capacity
load
(pF)
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
Drive
capability
IOH
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
IOL
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
6 mA
Note 1: These pins (TEST(3:1)) must not be left open. For the required connection please consult the TPS-1 User
Manual.
Note 2: The GPIO pins GPIO_00 to GPIO_47 can be configured as diagnosis input lines (local IO mode). The GPIO pins
are configured into groups of 8 bit. Unused diagnosis inputs must have a pull-down or pull-up resistor (depending
on customer’s design). A missing termination can cause undefined diagnosis.
Note 3: Generally unused GPIO pins should be pulled up (10 kΩ to VDD33). From PROFINET stack version V1.4
onwards all unused GPIOs should be left open, because the stack will configure them to outputs. This does not
apply to pins handled in note 2.
Abbreviations:
I
O
I/O
Input
Output
Input/Output
R19DS0069EJ0105 Rev. 1.05
Dec 16, 2016
page 19 of 39