M35071 Datasheet, PDF (14/40 Pages) Mitsubishi Electric Semiconductor – SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS

MITSUBISHI MICROCOMPUTERS
M35071-XXXSP/FP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(6) Address 12516
DA Register
Status
Contents
Function
Remarks
0
LIN2
0 _{The vertical dot size for line n in the character dot lines (18 vertical Character size setting in the vertical}
1 ^{lines) is set using LINn (n = 2 to 17).}
direction for the 2nd line.
1
LIN3
0 _{Dot size can be selected between 2 types for each dot line.}
1
Character size setting in the vertical
direction for the 3rd line.
For dot size, see the below registers. Line 1 and lines 2 to 12 can
2
LIN4
0 _{be set independent of one another.}
1
LINn = “0”
LINn = “1”
Character size setting in the vertical
direction for the 4th line.
0
3
LIN5
1
1st line
Refer to VSZ1L0 Refer to VSZ1H0
and VSZ1L1
and VSZ1H1
2nd to 12th Refer to VSZ2L0 Refer to VSZ2H0
line
and VSZ2L1
and VSZ2H1
Character size setting in the vertical
direction for the 5th line.
0
4
LIN6
1
Character size setting in the vertical
direction for the 6th line.
0
5
LIN7
1
Character size setting in the vertical
direction for the 7th line.
0
6
LIN8
1
Character size setting in the vertical
direction for the 8th line.
0
7
LIN9
1
Character size setting in the vertical
direction for the 9th line.
0 H: Cycle with the horizontal synchronizing pulse
8
V1SZ0
1
V1SZ1 V1SZ0 Vertical direction size
0
0
1H/dot
0
9
V1SZ1
1
0
1
1
0
1
1
2H/dot
3H/dot
4H/dot
Character size setting in the vertical
direction for the 1st line.
(display monitor 1 to 12 line)
0 H: Cycle with the horizontal synchronizing pulse
A
VSZ1L0
1
VSZ1L1 VSZ1L0 Vertical direction size
0
0
1H/dot
0
B
VSZ1L1
0
1
1
0
2H/dot
3H/dot
1
1
1
4H/dot
Character size setting in the vertical
direction (display monitor 1 line) at “0”
state in register LIN2 to LIN17
(address 12516, 12616).
0 _{H: Cycle with the horizontal synchronizing pulse}
C
VSZ1H0
VSZ1H1 VSZ1H0 Vertical direction size
1
0
0
1H/dot
0
D
VSZ1H1
1
0
1
1
0
1
1
2H/dot
3H/dot
4H/dot
Character size setting in the vertical
direction (display monitor 1 line) at “1”
state in register LIN2 to LIN17
(address 12516, 12616).
0 It should be fixed to “0”.
E
TEST10
(Note 3)
1 Can not be used.
____
Notes 1. The mark around the status value means the reset status by the "L" level is input to AC pin.
2. The page in which data is written is controlled by the DAF bit. When set to "0", data is written into page 0, whereas when set to "1",
data is written into page 1.
3. Registers marked with (Note 3) are found only in page 0, therefore the register value does not change when the DAF bit is set to "1".
13