32C88T Datasheet, PDF (14/59 Pages) Renesas Technology Corp – SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER

M32C/88 Group (M32C/88T)
1. Overview
1.6 Pin Description
Table 1.6 Pin Description (100-Pin and 144-Pin Packages)
Classsfication Symbol I/O Type
Function
Power Supply VCC
I
VSS
Analog Power AVCC
I
Supply
AVSS
____________
Reset Input RESET
I
CNVSS
CNVSS
I
Input to Switch BYTE
I
External Data Bus
Width
Main Clock Input XIN
I
Main Clock Output XOUT
O
Sub Clock Input XCIN
I
Sub Clock output XCOUT
O
Clock Output CLKOUT
O
______
________
INT Interrupt INT0 to
I
________
Input
INT5
_______
_______
NMI Interrupt Input NMI
I
_____
_____
Key Input Interrupt KI0 to KI3
I
Timer A
TA0OUT to I/O
TA4OUT
TA0IN to
I
TA4IN
Timer B
TB0IN to
I
TB5IN
___
___
Three-phase Motor U, U, V, V, O
___
Control Timer Output W, W
_________
________
Serial I/O
CTS0 to CTS4 I
_________ _________
RTS0 to RTS4 O
CLK0 to
I/O
CLK4
RxD0 to
I
RxD4
TxD0 to
O
I²C Mode
TxD4
SDA0 to
I/O
SDA4
SCL0 to
SCL4
Serial I/O
STxD0 to
O
Special Function STxD4
SRxD0 to
I
SRxD4
_______
_______
SS0 to SS4 I
Apply 4.2 to 5.5 V to both VCC pins.
Apply 0 V to the VSS pin
Supplies power to the A/D converter. Connect the AVCC pin to VCC and the
AVSS pin to VSS
___________
The microcomputer is in a reset state when "L" is applied to the RESET pin
Switches processor mode. Connect the CNVSS pin to VSS
Connect the BYTE pin to VSS
I/O pins for the main clock oscillation circuit. Connect a ceramic resonator
or crystal oscillator between XIN and XOUT. To apply external clock, apply it
to XIN and leave XOUT open.
I/O pins for the sub clock oscillation circuit. Connect a crystal oscillator
between XCIN and XCOUT. To apply external clock, apply it to XCIN and
leave XCOUT open
Outputs the clock having the same frequency as fC, f8 or f32
______
Input pins for the INT interrupt
_______
Input pin for the NMI interrupt
Input pins for the key input interrupt
I/O pins for the timer A0 to A4
(TA0OUT is a pin for the N-channel open drain output.)
Input pins for Timer A0 to A4
Input pins for Timer B0 to B5
Output pins for the three-phase motor control timer
Input pins for data transmission control
Output pins for data reception control
Inputs and outputs the transfer clock
Inputs serial data
Outputs serial data
(TxD2 is a pin for the N-channel open drain output.)
Inputs and outputs serial data
(SDA2 is a pin for the N-channel open drain output.)
Inputs and outputs the transfer clock
(SCL2 is a pin for the N-channel open drain output.)
Outputs serial data when slave mode is selected
(STxD2 is a pin for the N-channel open drain output.)
Inputs serial data when slave mode is selected
Input pins to control serial I/O special function
I : Input O : Output I/O : Input and output
Rev. 1.10 Oct. 31, 2005 Page 14 of 57
REJ03B0171-0110