M16C62M Datasheet, PDF (12/25 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

Electrical characteristics (Vcc = 3V)
Mitsubishi microcomputers
M16C / 62M (80-pin version) Group
(Low voltage version)
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
VCC = 3V
Table 1.20.7. Electrical characteristics (referenced to VCC = 2.7V to 3.6V, VSS = 0V at Ta = – 20^oC
to 85^oC / – 40^oC to 85^oC(Note 1), f(XIN) = 10MHz without wait unless otherwise
specified)
Symbol
Parameter
Measuring condition
P00 to P07, P20 to P27, P30 to P37,
VOH
HIGH output P40 to P43, P50 to P57, P60 to P67,
voltage
P76, P77, P80 to P84, P86, P87,
P90, P92 to P97, P100 to P107
IOH=–1mA
VOH
HIGH output XOUT
voltage
HIGHPOWER
LOWPOWER
IOH=–0.1mA
IOH=–50µA
HIGH output _XCOUT
voltage
HIGHPOWER
LOWPOWER
With no load applied
With no load applied
P00 to P07, P20 to P27, P30 to P37,
VOL
LOW output ^{P40 to P43, P50 to P57, P60 to P67,}
IOL=1mA
voltage
P70, P71, P76, P77, P80 to P84, P86,
P87, P90, P92 to P97, P100 to P107
VOL
LOW output _XOUT
voltage
HIGHPOWER
LOWPOWER
IOL=0.1mA
IOL=50µA
LOW output _XCOUT
voltage
HIGHPOWER
LOWPOWER
With no load applied
With no load applied
Standard
Min. Typ. Max. ^Unit
2.5
V
2.5
2.5
V
3.0
V
1.6
0.5 V
0.5
0.5 ^V
0
V
0
VT+-VT-
VT+-VT-
Hysteresis
Hysteresis
TA0IN, TA3IN, TA4IN,
TB0IN, TB2IN to TB5IN, INT0 to INT2,
ADTRG,CTS0,CTS1 CLK0,CLK1,CLK3,
CLK4, TA3OUT, TA4OUT, NMI, KI0 to KI3,
SIN4, RXD0 to RXD2
RESET
HIGH input P00 to P07, P20 to P27, P30 to P37,
current
P40 to P43, P50 to P57, P60 to P67,
II H
P70, P71, P76, P77, P80 to P87,
VI=3V
P90, P92 to P97, P100 to P107,
XIN, RESET, CNVss (BYTE)
LOW input P00 to P07, P20 to P27, P30 to P37,
current
P40 to P43, P50 to P57, P60 to P67,
I IL
P70, P71, P76, P77, P80 to P87,
VI=0V
P90, P92 to P97, P100 to P107,
XIN, RESET, CNVss (BYTE)
0.2
0.8 V
0.2
1.8 V
4.0 µA
–4.0 µA
Pull-up
RPULLUP _resistance
P00 to P07, P20 to P27, P30 to P37,
P40 to P43, P50 to P57, P60 to P67,
P76, P77, P80 to P84, P86,P87,
P90, P92 to P97, P100 to P107
VI=0V
RfXIN
RfXCIN
VRAM
Feedback resistance XIN
Feedback resistance ^XCIN
RAM retention voltage
When clock is stopped
The output pins Mask ROM version
are open and
other pins are
VSS
Flash memory 3V
version
f(XIN)=10MHz
Square wave, no division
f(XIN)=10MHz
Square wave, no division
Mask ROM version
Flash memory 3V
version
f(XCIN)=32kHz
Square wave
Flash memory 3V
version
Program
f(XIN)=10MHz
Square wave, division by 2
Icc
Power supply current
Flash memory 3V
version
Erase
Mask ROM version
Flash memory 3V
version
f(XIN)=10MHz
Square wave, division by 2
f(XCIN)=32kHz
When a WAIT instruction
is executed.
Oscillation capacity High
(Note2)
f(XCIN)=32kHz
When a WAIT instruction
is executed.
Oscillation capacity Low
(Note2)
Ta=25°C
when clock is stopped
Note 1: Specify a product of -40°C to 85°C to use it.
Note 2: With one timer operated using fC32.
Ta=85°C
when clock is stopped
20
75 300 KΩ
3.0
MΩ
10.0
MΩ
2.0
V
9.5 21.25 mA
12.0 21.25 mA
45.0
µA
14.0
mA
17.0
mA
2.8
µA
0.9
µA
1.0
µA
20.0
11