M61530FP Datasheet, PDF (10/19 Pages) Renesas Technology Corp – 4ch Electronic Volume with 5.1ch Analog Input

M61530FP
Electrical characteristics
Unless otherwise noted, Ta = 25°C, Vcc = 9 V, f = 1 kHz, input gain control = 0 dB, bass boost = off, trim/master
volume = 0 dB, FL/FR output SW = on, SL/SR VOL input SW = SL/SR input, LFE MIXS SW = on, SW MIX= off,
output gain control = 0 dB
Limits
Item
Symbol Min. Typ. Max. Unit Condition
Power Circuit current IACC
supply

14
25
mA
When no signal is detected, current flows to pin 16
I/O
Max. input
VIM1
1.6 2.0

Vrms Pins 2, 37, 40, and 41: Input, pins 1, 38, 39, and 42:
voltage
Output, RL = 10 kΩ, THD = 1%
VIM2
0.8 1.0

Vrms
Pins 6, 10, and 13: Input, pins 5, 9, and 12: Output, RL =
10 kΩ, THD = 1%
VIM3
1.6 2.0

Vrms
Pin 14: Input, pin 22: Output, RL = 10 kΩ, THD = 5%, f =
100 kHz
Absolute max. AVIM
input voltage


2.0
Note
Vrms
Pins 3, 7, 14, and 15: Input
Max. output VOM1
1.8 2.4

voltage
Vrms
Pins 6 and 10: Input, pins 29 and 26: Output, RL = 10 kΩ,
THD = 5%, bass boost = on, f = 100 Hz
VOM2
1.6 2.0

Vrms Pin 13: Input, pin 25: Output, RL = 10 kΩ, THD = 5%
VOM3
1.4 1.8

Vrms
Gain between pins 14 and 22, Vi = 0.5 Vrms, FLAT, f = 100
Hz
Bypass gain GV1
+2.3 +4.3 +6.3 dB
Gain from pins 6 to 29, pin 10 to 26, and pins 13 to 25, Vi =
0.5 Vrms, FLAT
GV2
-2
0
+2
dB
Gain from pins 2 to 32 and 41 to 34, Vi = 0.5 Vrms, FLAT
GV3
-2
0
+2
dB
Gain from pin 14 to 22, Vi = 0.5 Vrms, FLAT, f = 100 Hz
Output noise
voltage
Vno1

6.0
12.0 µVrms DIN-Audio, when no signal is


2.5
8.0
µVrms ^{present, Rg = 0 for pins 6 and}
SL/SR ch volume = -∞
10, pins 29 and 26 are outputs _dB
Vno2

6.0
10.0 µVrms DIN-Audio, when no signal is
C ch volume = 0 dB

2.0
4.0
µVrms ^{present, Rg = 0 for pin 13, pin 25} C ch volume = -∞ dB
is an output
Vno3

6.5
16.0 µVrms DIN-Audio, when no signal is
LFE ch volume = 0 dB

6.5
16.0 µVrms ^{detected, Rg = 0 for pin 14, pin} LFE ch volume = -∞ dB
22 is an output, SW ch LPF:
fc=300 Hz
Total
harmonic
distortion rate
THD1
THD2

0.003 0.2
%

0.003 0.1
%
Pins 6 and 10: input, pins 29 and 26: output, bandwidth:
400 Hz to 30 kHz, Vo = 0.5 Vrms, RL = 10 kΩ
Pin 13: input, pin 25: output, bandwith: 400 Hz to 30 kHz,
Vo = 0.5 Vrms, RL = 10 kΩ
THD3

0.008 0.2
%
Pin 14: input, pin 22: output, 30-kHz low-pass filter, Vo =
0.5 Vrms, RL = 10 kΩ, output gain control = 0 dB, when
AGC is not operating, f = 100 Hz
THD4

2

%
Pin 14: input, pin 22: output, 30-kHz low-pass filter, RL = 10
kΩ, Vi = 700 mVrms, f = 100 Hz, when AGC is operating,
output gain control = + 12 dB
Volume max. ATT
attenuation

-100 -87
dB
Vo = 1 Vrms, pins 22, 25, 26, and 29 are outputs, JIS-A,
volume = -∞
Rev.1.0, Sep.19.2003, page 10 of 18