ZBH01002 Datasheet, PDF (4/4 Pages) Red Lion Controls. Inc – MODELS ZBG AND ZBH STANDARD DUTY ENCODER

WHEELS & REPLACEMENT TIRES FOR CODE OR WHEELS
ORDERING INFORMATION
WHEEL CODE
OR
CIRCUMFERENCE
1 foot (1/3 yd)
1/3 meter
4/10ths yard
4/10ths meter
1 foot (1/3 yd)
TOLERANCE
±0.40%
±0.40%
±0.40%
±0.40%
±0.35%
OF
BF (Balanced)
1/3 meter
4/10ths yard
4/10ths meter
1 foot (1/3 yd)
±0.30%
±0.30%
±0.30%
±0.40%
PART NUMBER
WF1000OR
WM0333OR
WY0400OR
WM0400OR
WF1000OF
WM0333OF
WY0400OF
WM0400OF
WF1000BF
WHEEL CODE
OK
BK (Balanced)
Replacement Tires
for OR Wheels
CIRCUMFERENCE
1 foot (1/3 yd)
1/3 meter
4/10ths yard
4/10ths meter
1 foot (1/3 yd)
1 foot (1/3 yd)
1/3 meter
4/10ths yard
4/10ths meter
TOLERANCE
±0.35%
±0.30%
±0.30%
±0.30%
±0.35%
Note: After installation of measuring wheels, ensure guards,shields or other
devices are in place to protect personnel from rotating equipment.
PART NUMBER
WF1000OK
WM0333OK
WY0400OK
WM0400OK
WF1000BK
TORF1000
TORM0333
TORY0400
TORM0400
MODEL LSAHC - LENGTH SENSOR HINGE CLAMP ASSEMBLY
The Length Sensor Hinge Clamp Assembly provides an easy method for
attachment and mounting of the Length Sensors and LSCB1 Conversion
Bracket. The removable top on the solid zinc LSAHC mounting block
allows quick installation of the Length Sensor handle tube and provides
secure clamping retention. The mounting block pivots freely in zinc right
angle brackets to allow mounting the assembly via clearance holes for 1/4"
dia. bolts.
The lock washers must be used as indicated (between the bolt head and
the top clamp piece). Assemble the top clamp piece as follows.
1. Tighten both bolts so that the top clamp half draws down evenly on
the sensor tube.
2. Tighten the bolts until both lock washers are flat.
3. Then turn each bolt an additional ½ to ¾ turn.
DIMENSIONS In inches (mm)
FRONT
VIEW
2.5 (63.5)
1.25
(31.8)
Lock washers (2) must be
installed between bolt heads
and top clamp piece.
.25 (6.3)
.85
(21.6)
SINGLE WHEEL
2.93 (74.4)
DUAL WHEEL 4 (101.6)
Model ZGH Shown
CAUTION: Downward tension
on signal cable can cause
wheel(s) to lift. Make sure
cable is clamped to
machine frame near
encoder and allow slack.
NOTE: The weight at the
Length Sensor unit
provides sufficient traction
for accurate operation
when mounted as shown,
with arm angle from
horizontal not exceeding
±30°, and with hinge clamp
toward the far extreme of
the extension arm.
3.4
(86.4)
2.9
(73.7)
TOP
VIEW
1.50
2.00 ^(38.1)
(50.8)
0.75
(19.0)
4X Ø 0.31 (7.9)
0.75 (19.0)
E-clip retaining ring (2)
must be installed in slots.
.88
(22.4)
WRHAEDEIULS
6.9 ^(175.3)
(14.98.3)
.88 (22.4)
4.50 (114.3)
5.70 (144.8)
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
LSAHC Length Sensor Hinge Clamp Assembly
PART NUMBER
LSAHC001
Model ZFH Shown
Length Sensors should be mounted so measuring
wheel(s) contact ribbon, strip or web as it passes over
a roller. As an alternative, wheel(s) can be driven by
roller surface next to material being measured.
Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]
Red Lion Controls
Europe
Softwareweg 9
NL - 3821 BN Amersfoort
Tel [phone]
Fax [phone]
Red Lion Controls
India
201-B, 2nd Floor, Park Centra
Opp 32 Mile Stone, Sector-30
Gurgaon-122002 Haryana, India
Tel [phone]
Red Lion Controls
China
Unit 302, XinAn Plaza
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel [phone]
Fax [phone]