XCHSPA00 Datasheet, PDF (1/4 Pages) Red Lion Controls. Inc – MODEL XCHSPA – HSPA+ CELLULAR MODEM OPTION CARD FOR DATA STATION PLUS, MODULAR CONTROLLER AND PTV

Tel [phone]
Fax [phone]
www.redlion.net
Bulletin No. XCHSPA-B
Drawing No. LP0966
Released 04/15
MODEL XCHSPA – HSPA+ CELLULAR MODEM OPTION CARD FOR DATA
STATION PLUS, MODULAR CONTROLLER AND PTV
zz SUPPORTS HSPA+ CELLULAR DATA CONNECTIVITY WITH FALL
BACK TO 3G AND 2G
zz UP TO 21 MBPS DOWNLINK/5.76 MBPS UPLINK SPEEDS
zz CONFIGURED USING CRIMSON^® 3.0 SOFTWARE
zz FOR INSTALLATION WITH A DATA STATION PLUS, A MODULAR
CONTROLLER MASTER OR A ProducTVity STATION (PTV)
zz INSTALLATION AND CONNECTION HARDWARE ARE INCLUDED
WITH CARD
GENERAL DESCRIPTION
The XCHSPA option card allows the user to add HSPA+ cellular modem
capability to their Data Station Plus, Modular Controller Master or PTV. The
cellular standard adopted in this option card is HSPA+ with fallback capability
to 3G and 2G. It can get speeds up to 21 Mbps downlink and 5.76 Mbps uplink.
It’s built upon the GSM standard and widely available throughout the world.
HSPA+ can be used for services such as Wireless Application Protocol (WAP)
access, Short Message Service (SMS), and for Internet connectivity.
The XCHSPA option card is penta-band, allowing it to work in frequencies
across the Americas, Europe and Asia. US and Canada work in the 850/1900
MHz bands, while Europe, Middle East, Africa and most of Asia work in the
900/1700/2100 MHz HSPA+ frequencies.
The XCHSPA requires the addition of a SIM (Subscriber Identity Module)
card, which is inserted into the holder prior to installation of the XCHSPA card.
The SIM card securely stores the service-subscriber key (IMSI) used to identify
a subscriber, and is used to connect to the network to obtain an IP address from
the provider.
The XCHSPA communication card is easily installed by removing the blank
expansion port cover of your Data Station Plus, Modular Controller Master or
PTV and plugging the XCHSPA card into the expansion port. Configuration is
simple using Red Lion’s free Crimson^® 3.0 software.
CONTENTS OF PACKAGE
- XCHSPA option card
- This hardware bulletin
ORDERING INFORMATION
MODEL NO.
XCHSPA
ANT
DESCRIPTION
GSM/HSPA+ Modem Option Card ¹
PART NUMBER
XCHSPA00
2G/3G 3" hinged antenna
ANT-TG090113
2G/3G/4G LTE low profile direct
permanent mount antenna, IP67 rated
ANT-G30B108111
2G/3G 4.5" whip magnetic mount antenna,
IP65 rated
ANT-GA107201111
2G/3G low profile direct permanent mount
antenna, IP65 rated
ANT-G21B301111
1 _{Antenna is NOT included with the card. Must be purchased separately if}
needed.
SAFETY SUMMARY
All safety related regulations, local codes and instructions that appear in the
literature or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
Do not use the controller to directly command motors, valves, or other
actuators not equipped with safeguards. To do so can be potentially harmful to
persons or equipment in the event of a fault to the controller.
CAUTION: Risk of Danger.
Read complete instructions prior to
installation and operation of the unit.
SPECIFICATIONS
1. POWER REQUIREMENTS:
HSPA+ Mode: During continuous active webserver traffic
Instantaneous maximum: 24 V @ 300 mA
Average:
24 V @ 200 mA
GPRS Mode:
Instantaneous maximum: 24 V @ 650 mA (1.1 msec every 4.6 msec)
Average:
24 V @ 275 mA
Power is supplied to the option card from the main board of the Modular
Controller Master, Data Station Plus or PTV.
2. LINK STATUS LEDs:
Link Status - Link Status LED shows cellular link condition.
3. COMMUNICATIONS:
Isolation from XCHSPA Antenna connector to Modular Controller
Master, Data Station Plus or PTV: 500 VDC for 1 minute.
2. ANTENNA CONNECTOR:
SMA Female connector requires:
50 Ohm antenna with SMA male connector
Penta-band HSPA+ antenna (850/900/1700/1900/2100 MHz) for global
support.
Dual-band (850/1900 MHz) antenna for US and Canada only
Dual band (900/2100 MHz) for Europe only
Voltage Standing Wave Ratio (VSWR) should not exceed 2.0:1
The antenna cable should be 50Ω impedance, RG178/U or RG174/U type
and be able to connect to the RSMA (Male) jack bulkhead. The antenna
could be horizontal, vertical or right angled. Longer antenna cable would
equate to signal loss. This device is intended for connection to an antenna
mounted within the building or a UL certified enclosure suitably rated for
application.
1