PTC150PT-1R00-FB Datasheet, PDF (1/1 Pages) RCD COMPONENTS INC. – PLATINUM, NICKEL, NICKEL IRON RTD’s TEMPERATURE RATING UP TO 500°C

PLATINUM, NICKEL, NICKEL IRON RTD’s
TEMPERATURE RATING UP TO 500°C
PTC SERIES- Ceramic Case
PTS SERIES- Stainless Steel
RoHS
Term.W is
RoHS
compliant
RESISTORS CAPACITORS COILS DELAY LINES
B
↑
↓
↓^d
↑
← A→
Inherent wirewound stability
Resistance range: 1Ω to 1000Ω
Tolerance available to ±0.1%
Wide selection of TC’s (+3850 to +6720ppm)
Excellent linearity and thermal response time
RCD’s Resistance Temperature Detectors are designed for tough
industrial applications, and are utilized to sense or regulate air (PTC) or
liquid (PTS) environments. Series PTC feature an all-welded wirewound
construction for increased durability under stress and vibration, and
exceptional stability. PTS probes are encased in a stainless steel sheath
and are available with WW or film elements.
RCD
Type
Resistance
Wire
TCR
TC 3-digit Resistance
A
B
0° to 100°C code Range (Ω ) ±.060 [1.5] ±.01 [.25]
PTC100PT Platinum
3850ppm
392
1 - 200
PTC100CPN Chem. Pure Nickel
6720ppm
672
PTC100N
Nickel 270
6000ppm
603
1 - 120
1 - 120
.575 [14.6] .096 [2.44]
PTC100NF Nickel Iron
5150ppm
522
1 - 500
PTC150PT Platinum
3850ppm
392
1 - 400
PTC150CPN Chem. Pure Nickel
6720ppm
672
PTC150N
Nickel 270
6000ppm
603
1 - 200
1 - 200
.575 [14.6] .125 [3.18]
PTC50NF
Nickel Iron
5150ppm
522
1- 1000
PTC200PT Platinum
3850ppm
392
1- 400
PTC200CPN Chem. Pure Nickel
6720ppm
672
PTC200N
Nickel 270
6000ppm
603
1 - 200
1 - 200
.675 [17.1] .170 [4.32]
PTC200NF Nickel Iron
5150ppm
522
1 - 1000
* Lead material is nickel for minimal oxidation at high temperature on platinum elements, tinned copperweld is standard on others.
C*
Typ. [.05]
.016 [.4]
Lead Length 0.5 [12.7] min.
.016 [.4]
Lead Length 0.5 [12.7] min.
.020 [.5]
Lead Length 1.0 [25.4] min
LINEARITY
4.0
3.5
3.0
2.5
2.0
1.5
CP NICKEL
NICKEL 270
NICKEL IRON
COPPER
PLATINUM
WIRE COMPARISON
Wire Alloy
Platinum
CP Nickel
Nickel 270
Nickel Iron
Cost
Medium
High
Low
Low
Temp. Range
-55 to +500°C
-55 to +300°C
-55 to +300°C
-55 to +260°C
Linearity
Excellent
Fair
Fair
Fair
R/T Curve Repeatability
Excellent
Good
Fair
Good
THERMAL RESPONSE (TIME CONSTANT) varies with different element sizes, resistance values, and wire alloy.
Typical time constant for PTC 150 PT 100 ohm is 2.2 seconds in water moving 3ft./sec. Consult factory for details.
SELF-HEATING is contingent upon resistance value, alloy, and element size. Typical self-heating for PTC 150 PT
100 ohm is 65 mW/°C in water moving at 3ft./sec. Consult factory for particular specifications.
INTERCHANGEABILITY - The strain-free design of RCD sensors insures maximum repeatability. This characteristic
is degraded by lot-to-lot inconsistencies of the various wire alloys. Platinum being extremely consistant allows the
best interchangeability characteristics. Consult factory for specific data based on particular alloy and tolerance.
SHOCK AND VIBRATION - PTC elements withstand 100 G’s sinewave shock for 3 cycles at 10 milliseconds, and
withstand vibration 10Hz to 2200Hz at 20 G’s.
1.0
0
0 100 200 300 400 500 600
32 212 392 572 752 932 1112
TEMPERATURE
°C
°F
P/N DESIGNATION:
PTC150PT - 1000 - F B
RCD Type
Resis. Code: 3 signif. digits & multiplier (1R00=1Ω, 10R0=10Ω, 1000=100Ω, etc.)
Tolerance Code: F=1%, D=0.5%, C=0.25%, B=0.1%
Packaging: B = Bulk
Temp. Coefficient: 3 digit code rounded to nearest 100 (392=3850ppm, 603=6000ppm, etc.)
Termination: W= Lead-free, Q= Tin/Lead (leave blank if either is acceptable)
392 W
RTD PROBES, TEMPERATURE RATING UP TO 500°C
PTS SERIES
OPTIONAL
1111222233334444555566667777888899991111222233334444555566667777888899990000
Series PTC (wirewound) and PT (thin-film) RTD elements can be assembled
into stainless steel sheaths for severe environmental requirements. These
probes (PTS Series) are moistureproof and pressure tight and in many
instances may be directly inserted into process lines or thermowells for
precise temperature readings. Series PTS is available in any standard PTC
resistance value and temperature coefficient, in .125” [3.18], .187 [4.75],
.250 [6.35] diameters. Teflon insulated leads are standard (other insulations
available). 2-terminal, 3-terminal, or 4-terminal configurations available.
Probe lengths available from 0.5” [12.7] to 18” [457]. Consult factory for
list of standard probe styles including surface measurement,
flange mount, screw mount, etc.
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: [phone] Fax: [phone] Email:[e-mail]
FA097 Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
86