ML2010V-R100-FB Datasheet, PDF (1/1 Pages) RCD COMPONENTS INC. – LOW-OHM CHIP RESISTORS, 0.1W TO 3W

LOW-OHM CHIP RESISTORS, 0.1W TO 3W
ML SERIES
RoHS
Term.W is
RoHS
compliant
& 260°C
compatible
RESISTORS CAPACITORS COILS DELAY LINES
t
T
Industry’s widest range and lowest cost!
Values as low as 0.0005Ω, current ratings to 60 Amp
High power to size ratio
Non-inductive
OPTIONS
Option V: 170°C operating temperature range
Option EK: Group A screening per MIL-R-10509
Option EL: Group A & B screening per MIL-R-10509
L
W
RCD’s ML series offers cost-effective solutions for low
resistance applications and are particularly ideal for various
types of current sensing, voltage dividing, battery and pulse
circuits, including linear and switching power supplies, power
amplifiers, consumer electronics, etc. The resistance element is
thick film or metal plate, and is coated with high temperature
insulation for exceptional environmental protection.
RCD
Type
Max.
Max.
Wattage * Current *
(70°C) (70°C)
Resistance
Range
Typical TC Optional TC
(ppm/°C)
(ppm/°C)
L
W
T
t
0.02Ω TO 0.049Ω
400
ML0402 0.1W
3A
0.050Ω TO 0.099Ω
300
0.100Ω TO1.0Ω
200
0.01Ω TO 0.049Ω
400
ML0603 0.125W 3.5A 0.050Ω TO 0.099Ω
300
0.100Ω TO1.0Ω
200
0.01Ω TO 0.049Ω
400
ML0805 0.25W
5A
0.050Ω TO 0.099Ω
300
0.100Ω TO1.0Ω
200
200, 100
200, 100
100
200, 100
200, 100
100
200, 100
200, 100
100
.040 ± .004 .020 ± .004 .014 ± .004 .010 ± .004
[1.00 ± .1] [.5 ± .1] [.35 ± .1] [.25 ± .1]
.061 ± .005 .031 ± .004 .016 ±. 006 .012 ± .008
[1.55 ± .12] [.8 ± .1] [.40 ± .15] [.3 ± .2]
.079 ± .008 .050 ± .008 .020 ± .006 .024 ± .008
[2.0 ± 0.2] [1.25 ± 0.2] [0.5 ± .15] [0.6 ± 0.2]
0.01Ω TO 0.049Ω
400
ML1206 0.5W
7A
0.050Ω TO 0.099Ω
300
0.100Ω TO1.0Ω
200
0.01Ω TO 0.049Ω
400
ML2010 1W
14A
0.050Ω TO 0.099Ω
300
0.100Ω TO1.0Ω
200
0.01Ω TO 0.049Ω
400
ML2512 2W
20A
0.050Ω TO 0.099Ω
300
0.100Ω TO1.0Ω
200
200, 100
200, 100
100
200, 100
200, 100
100
200, 100
200, 100
100
.126 ± .008 .063 ± .008 .020 ± .006 .030 ± .018
[3.2 ± 0.2] [1.6 ± 0.2] [0.5 ± .15] [0.76 ± .46]
.197 ± .008 .098 ± .008 .020 ± .006 .032 ± .020
[5.0 ± 0.2] [2.5 ± 0.2] [0.5 ± .15] [0.8 ± 0.5]
.250 ± 0.01 .126 ± .012 .024 ± .008 .040 ± .020
[6.35 ± 0.25] [3.2 ± 0.3] [0.6 ± .2] [1 ± 0.5]
0.0005Ω
350
MLB2512 2W/ 3W * 60A
0.00075Ω, 0.001Ω,
0.0015Ω, 0.002Ω
200
0.0025Ω TO 0.01Ω
150
200, 100
100, 50
100, 50
.250 ± 0.01 .126 ± .012 .020~.063** .040~.106**
[6.35 ± 0.25] [3.2 ± 0.3] [0.5 ~ 1.6] [1.0 ~ 2.7]
* In order to operate at maximum wattage and current ratings, a suitable substrate or PCB design is required to carry the current and drain the heat. Heavy Cu, large
pads and traces, and/or multilayer PC boards are recommended. MLB2512 has a 3W rating when used with 300mm² x .0056 Cu pads
** Varies with resistance value (lower values typically have thicker bodies and wider termination pads for increased current carrying capability)
TYPICAL PERFORMANCE CHARACTERISTICS
Characteristics
Thermal Shock (-55° to +155°C)
Short Time Overload (2x [PxR]^1/2, 5 sec.)
Low Temp. Operation (-55°C)
High Temp. Exposure (125°C, 100 hrs.)
Resistance to Solder Heat
Moisture Resistance
Load Life(1000 hrs.)
Operating Temperature Range
Derating of Wattage & Current
Solderability
Terminal Adhesion
∆R
±1%
±2%
±1%
±1%
±0.5%
±1%
±2%
-55 to +155°C
1.177%/°C above 70°C
95% Min. Coverage
15 Grams Min.
P/N DESIGNATION:
ML2010 - R01 - J T W
RCD Type
Options: V, EK, EL (leave blank if standard)
Resis. Code: for 1% tol. use R as decimal point and 3
digits, e.g. R100= 0.1Ω, R200=.2Ω; for 2%-10% use R
and 2 digits , e.g. R10= 0.1Ω, R20= .2Ω, etc. except if
necessary, use additional (significant) digits, e.g. R005 for
0.005Ω, R0075 for 0.0075Ω in any tolerance
Tolerance Code: F=1%, G=2%, J=5%
Packaging: B=Bulk, T=Tape & Reel
Optional TC: 50=50ppm, 101=100ppm, 201-200ppm
Termination: W= Lead-free, Q= Tin/Lead (leave blank if
either is acceptable)
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: [phone] Fax: [phone] Email:[e-mail]
FA009C Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
24