MGP50S-R100-F Datasheet, PDF (1/1 Pages) RCD COMPONENTS INC. – METAL FILM MELF RESISTORS

METAL FILM MELF RESISTORS
MGP SERIES - Conformal Coated
MHM SERIES - Hermetic Sealed
RoHS
Term.W is
RoHS
compliant
& 260°C
compatible
RESISTORS CAPACITORS COILS DELAY LINES
Industry’s widest selection of metal film MELF resistors-
.1W to .5W, 0.1Ω to 22MΩ, 0.1% to 5%, 10ppm to 100ppm/°C
Low cost, quick delivery (available on SWIFT^TM program)
Precision performance, excellent environmental stability
Series MHM hermetic sealed is an industry first!
OPTIONS
Option S: Increased power (refer to chart below)
Option P: Increased pulse capability
Option F: Flameproof coating (per UL94V0)
Dozens of additional options are available... burn-in, special
marking, non-standard values, high frequency designs,
matched sets, temp. sensitive, zero-ohm jumpers, etc.
Customized components are an RCD specialty!
Metal film performance, economical price!
RCD Series MGP melf* resistors utilize precision film technology
which is inherently low inductance, low noise, and high stability
even after extended periods. Heavy solder plating assures
excellent solderability and long shelf life. Series MHM offers
hermetically sealed environmental protection and utmost
reliability. MGP series parts are color banded, MHM are alphanu-
merically marked with resistance and tolerance. *Melf = metal
electrode face-bonded (cylindrical component).
L
W
D
Inch [mm]
SPECIFICATIONS
RCD
Type
Wattage
(Std)
Wattage
(Opt. 'S')
Voltage
Rating^{1, 2}
Resistance
Range²
Dielectric
Strength²
t
L±.012 [.3] D±.008 [.2]
W (Min.)
t (Max) ²
MGP45 .1W
.15W
100V
1Ω to 1M
200V
.079 [2.0]
.044 [1.12]
.012 [.3]
.003 [.076]
MGP50 .125W
.25W
200V
0.18Ω to 10M
250V
.135 [3.4]
.057 [1.45]
.02 [.5]
.004 [.1]
MGP55 .25W
.5W
250V
0.1Ω to 22M
350V
.232 [5.9]
.085 [2.15]
.024 [.6]
.006 [.15]
MHM55³ .125W
.25W
250V
10Ω to 200K
1 Max working voltage determined E= √(PxR), not to exceed the value listed.
350V
.275 [7.0]
.120 [3.05]
2 Consult factory for non-standard range
.050 [1.27]
3 Preliminary
.006 [.15]
PERFORMANCE
MGP Series* MHM Series*
TCR (10 & 15ppm avail on custom basis)
100ppm/°C std, 100ppm/°C std,
25&50ppm avail 25&50ppm avail
Operating Temperature Range
-55 to +155°C -65 to +175°C
PULSE WITHSTAND CHART (increased pulse levels avail.)
1000
Power Derating above 70°C
1.18%/°C
.95%/°C
100
Solderability (5 sec @ 230°C)
95% coverage 95% coverage
Insulation Resistance(Dry)
Short-Time Overload (5 sec. @ 2.5x
power not to exceed 2x voltage rating)
Resis. to Solder Heat (260°C, 5 sec.)
10,000MΩ
0.25%
(0.5% Opt.S)
0.2%
10,000MΩ
.025%
(.05% Opt.S)
.02%
Temperature Cycling (-50°C + 120°C)
0.5%
.02%
Moisture (Mil-Std202 M106 & Mil-R-55342)
0.5%**
.05%**
Load Life (1000 hours rated power)
0.5%(1%Opt.S) .1% (.2% Opt.S)
* Typical performance levels listed are for standard products from 10Ω to 1M.
Consult factory for performance levels of extended range and modified designs.
** To ensure utmost reliability, care should be taken to avoid potential sources of
ionic contamination
APPLICATION NOTE #1: Temperature Rise (T_HS)
The T_HS of SM resistors depends largely on heat conduction through the
end terminations, which can vary significantly depending on PCB
material and layout (i.e. pad size, trace area, copper thickness, air flow,
etc.). Typical temp. rise at full rated power is 30-50°C (Opt.S=50-70°C).
APPLICATION NOTE #2: Resistor Selection
MGP resistors are ideal for semi-precision SM applications and are
generally more economical than thin film rectangular chips. For less
critical applications, consider low cost MCF carbon film melf resistors.
For increased performance, especially in high humidity applications
(such as Naval or tropical environments), consider MHM series. If flat
chips are preferred, consider BLU series (precision) or MC series (semi-
precision/ general purpose). For higher power, consider MPF series.
10
MGP55SP
MGP50SP
MGP45SP
1
1uS
10uS
100uS
1mS
Pulse Duration
10mS
100mS
Pulse capability is dependent on res. value, waveform, repetition rate,
current, etc. Chart is a general guide for Opt. P pulse resistant version,
single pulse, with peak voltage levels not exceeding 1KV for MGP55SP,
700V MGP50SP, and 350V MGP45SP. Max pulse capability for standard
parts (w/o Opt.P) is 60% less. For improved performance and reliability,
a 30-50% pulse derating factor is recommended (or larger for frequent
pulses, high values, etc). Consult RCD for application assistance. Verify
selection by evaluating under worst-case conditions.
P/N DESIGNATION:
MGP50 - 1002 - F T W
RCD Type
Options: S, P, F (leave blank if std)
Resis. Code: ≤1%: 3 signif. figures & multiplier,
e.g. R100= 0.1Ω, 1R00= 1Ω, 10R0=10Ω,1000= 100Ω, 1001= 1KΩ.
Resis. Code 2% - 10%: 2 signif. figures & multiplier,
e.g. R10= 0.1Ω, 1R0= 1Ω,100= 10Ω, 101=100Ω,102= 1K, 103=10K.
Tolerance: F=1% (std), B=0.1%, C=.25%, D=.5%, G=2%, J=5%
Packaging : B = Bulk, T = Tape & Reel
Optional TC: 10=10ppm, 25=25ppm, 50=50ppm (leave blank if std)
Termination: W= Lead-free, Q= Tin/Lead (leave blank if either is acceptable)
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: [phone] Fax: [phone] Email:[e-mail]
FA031D Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
20