CL082V-10R0-G Datasheet, PDF (1/1 Pages) RCD COMPONENTS INC. – THICK FILM SIP NETWORKS

THICK FILM SIP NETWORKS
CL SERIES- Low Profile
C SERIES - High Power
. RCD CL101S
RESISTORS CAPACITORS COILS DELAY LINES
←New high density Sips, an RCD exclusive!
. RCD CL101
. RCD C101
Low cost, widest selection in the industry!
4-pin through 14-pin standard (2 through
20-pin sizes available on special order)
CL Series low-profile available from stock
RoHS
Term.W is
RoHS
compliant
& 260°C
compatible
(configuration1 & 2 in 6, 8, and 10-pin)
Wide resis. range: 10Ω to 3MΩ std., 1Ω to 1000M avail.
Bulk packaging is standard, tape or magazine tube avail.
R/2R Ladder Networks (Config. 7) offer 1/2LSB accuracy
from 4 to 10 bits
STANDARD CONFIGURATIONS
Configuration No. 1
......
1
>>> >>> >>> >>> >>> >>> >>>
Configuration No. 2
>>>
>>>
>>>
>>>
1
Configuration No. 3
.. ....
. . . . . . ^{R2>>> R2>>> R2>>> R2>>> R2>>> R2>>>}
. . . . . . ^{1 R1>>> R1>>> R1>>> R1>>> R1>>> R1>>>}
Configuration No. 4
......
1
>>> >>> >>> >>> >>> >>>
OPTION V - +200°C temperature Range
OPTION S - Super high density (.070” pin spacing)
OPTION P - Pulse tolerant design
OPTION N - Narrowline design (.070” thick)
OPTION F - Flameproof coating
OPTION C - Copper alloy terminals
Also available in custom circuits with multiple values/capacitors/
diodes, increased power & voltage, tolerance & TC matching, longer
pins, special marking, military burn-in, resis. values 1Ω to 1000M, etc.
DIMENSIONS
→ ← ^{.095 [2.4] Max.}
Opt. N= .070±.008
[1.8±.2]
→ ← ^{.011 [.28]}
Dimensions: Inch [mm]
←Length=0.1” X No. of pins max→
Pin #1
.
↑
C=.315 [8] Max.
CL=.195 [5] Max.
↓
→ ← ^{.020 [.5]} →
↑ _{.102 [2.6] Min.}
↓
← .100±.01 [2.54±.25]
Opt.S=.070± .01 [1.78 ±.25]
Configuration No. 5
1 ^>>>
>>> >>>
>>>
Configuration No. 6
vvv vvv vvv vvv vvv
1
Config. No. 7 R/2R
RR R
vvv vvv vvv
1 ^{>>> 2R >>> 2R >>> 2R >>> 2R >>> 2R}
GND LSB
MSB OUT
SINGLE RESISTOR
RCD POWER RATING*
PACKAGE POWER RATING*
Type
Config.
1,3,4,5,6
Config.
2
Config.
3, 7
4-Pin
6-Pin
7-Pin
8-Pin
9-Pin
10-Pin 12-Pin
C .3W .5W .17W 1W 1.5W 1.75W 2W 2.25W 2.5W 3W
CL .2W .3W .125W** .5W 1W 1.25W 1.5W 1.75W 2W 2.5W
* Reduce wattage ratings by 1/3 for Opt.S **Config. 7 n/a in CL Series
STANDARD VALUES- Config. 1, 2, 4, 5, 6:
10Ω to 3M in E-24 values (preferred values in bold type)-
10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43,
47, 51, 56, 62, 68, 75, 82, 91
STANDARD VALUES - Config. 3, Dual Terminator, R₁/R₂ :
81/130
160/260
220/270
330/470
120/195
162/260
220/330
330/680
121/195
180/390
330/390
3K/6.2K
R/2R LADDER NETWORKS (Config.7): 4Bit/6-pin, 5Bit/7-pin,
6Bit/8-pin, 7Bit/9-pin, 8Bit/10-pin, 9Bit/11-pin, and 10Bit/12-pin.
Available in Series C (low profile Series CL n/a). Linearity accuracy is
1/2LSB. Standard values are 5KΩ, 10KΩ, 25KΩ, 50KΩ, & 100KΩ ±2%.
P/N DESIGNATION:
CL 08 2 - 102 - G B W
Type: CL=low profile (std), C=high power
Number of Pins
Configuration Number
Options: V,S,P,N,F,C (leave blank if std)
Resis.Code 1%: 3 signif. figures & multiplier,
(e.g. 10R0=10Ω, 1000=100Ω, 1001=1K, 1004=1M)
Resis.Code 2%-5%: 2 signif. figures & multiplier,
(e.g. 100=10Ω, 101=100Ω, 102=1K, 103=10K, 104=100K, 105=1M)
When comprised of 2 res.values (config.3&7) separate
with /, e.g. 181/391=180Ω/390Ω
Tolerance Code: G=2% (standard), F=1%, J=5%
Packaging: B=bulk, A3=3 pin taping ammo pack, M=magazine tube
Opt. TC: 50=50ppm,101=100ppm (leave blank if standard)
Termination: W= Lead-free, Q= Tin/Lead (leave blank if either is acceptable)
DERATING (Series C and CL)
120
100
80
60
40
20
0
25 50 75 100 125 150
AMBIENT TEMPERATURE (°C)
DERATING (Option V)
120
100
80
60
40
20
0
40 80 120 160 200 240
AMBIENT TEMPERATURE (°C)
TYPICAL PERFORMANCE SPECIFICATIONS
Tolerance
Temperature Coefficient
TCR Tracking
Operating Temperature
Max. Working Voltage
Short Time Overload
Resis. to Solder Heat
Moisture Resistance
Terminal Strength
Thermal Shock
Load Life (1000 hours)
Temperature Cycling
Shock and Vibration
Lead Solderability
Marking
Terminals
2% Standard (1%, 5% avail.)
±100ppm typ (±250ppm <50Ω & >2.2M)
50PPM typical
-55°C to +125°C (+200°C Opt.V)
200V Series C, 100V Series CL & Opt.S
±0.5% (2.5x rated V, 5S, nte 2xW)
±0.25% (350°C, 5S)
±1%
±0.25%
±0.5%
±1.0%
±0.5%
±0.25%
Meets MIL-R-83401
Pin #1 ID, resis value, & tol as minimum
Solder plated steel typ., copper alloy* avail.
* RCD recommends use of copper alloy terminals (opt. C) in aqueous cleaning systems
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: [phone] Fax: [phone] Email:[e-mail]
FA032B Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
38