CO1 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – THROUGH HOLE CLOCK OSCILLATORS - TTL COMPATIBLE

THROUGH HOLE CLOCK OSCILLATORS - TTL COMPATIBLE
FEATURES
STANDARD 8 AND 14 PIN DIP PACKAGE
TOLERANCE AND STABILITY TO ± 25 PPM
LOW COST
AVAILABLE IN 3.3 VOLT
SPECIFICATIONS
SERIES
CO1
PACKAGE
14 PIN DIP
FREQUENCY RANGE
500.00 KHz TO 125.00 MHz
CO1100 : ±100 ppm
FREQUENCY STABILITY†
CO1050 : ±50 ppm
CO1025 : ±25 ppm
OPERATING TEMPERATURE RANGE
0° C TO +70° C STANDARD
-40° C TO +85° C EXTENDED
STORAGE TEMPERATURE RANGE
-55° C TO +125° C
VOLTAGE††
+5 VDC ±0.5 VDC
500.00 KHz TO 2.999 MHz: 30 mA
INPUT
CURRENT (MAX)
3.00 MHz TO 31.999 MHz: 50 mA
32.00 MHz TO 79.999 MHz: 70 mA
80.00 MHz TO 125.00 MHz: 80 mA
SYMMETRY
(AT 1.4 VDC LEVEL)
40 TO 60% NORMAL
45 TO 55% TIGHT
UNDER 9 MHz : ±15 ns MAX
OUTPUT
RISE AND FALL TIME
(0.4 - 2.4 VDC)
9 MHz TO 32 MHz : ±10 ns MAX
32 MHz TO 80 MHz : ±6 ns MAX
80 MHz TO 125 MHz : ±4 ns MAX
LOGIC "0" LEVEL
+0.5 V MAX, SINK TO 16 mA
LOGIC "1" LEVEL
+2.4 V MIN, SOURCE 0.4 mA
LOAD†††
1 TO 10 TTL STANDARD
SERIES CO1 AND CO13
CO13
8 PIN DIP
500.00 KHz TO 125.00 MHz
CO13100 : ±100 ppm
CO13050 : ±50 ppm
CO13025 : ±25 ppm
0° C TO +70° C STANDARD
-40° C TO +85° C EXTENDED
-55° C TO +125° C
+5 VDC ±0.5 VDC
500.00 KHz TO 2.999 MHz: 30 mA
3.00 MHz TO 31.999 MHz: 50 mA
32.00 MHz TO 79.999 MHz: 70 mA
80.00 MHz TO 125.00 MHz: 80 mA
40 TO 60% NORMAL
45 TO 55% TIGHT
UNDER 9 MHz : ±15 ns MAX
9 MHz TO 32 MHz : ±10 ns MAX
32 MHz TO 80 MHz : ±6 ns MAX
80 MHz TO 125 MHz : ±4 ns MAX
+0.5 V MAX, SINK TO 16 mA
+2.4 V MIN, SOURCE 0.4 mA
1 TO 10 TTL STANDARD
† FREQUENCYSTABILITYINCLUSIVE OF ROOMTOLERANCE ,
FREQUENCY STABILITY OVER TEMPERATURE, 10% POWER SUPPLY VARIATION, AGING, SHOCK,AND VIBRATION
†† +3.3 VOLT VERSION IS AVAILABLE. CONSULT RALTRON FOR SPECIFICATIONS
††† OUTPUT LOADS ALSO AVAILABLE AT 15 pF, 30 pF AND 50 pF. CONSULT RALTRON FOR SPECIFICATIONS
ENVIRONMENTAL AND TECHNICAL CONDITIONS
OUTPUT WAVEFORM
ENVIRONMENTAL
TEMPERATURE CYCLE
SHOCK
MIL-STD 883, METHOD 1010, 10 CYCLES -20° C TO 85° C
MIL-STD-202, METHOD 213, TEST CONDITION C
VCC
tf
tr
VIBRATION
MIL-STD-202, METHOD 204, TEST CONDITION A
RESISTANCE TO
SOLDERING HEAT
HUMIDITY
GROSS LEAK TEST
FINE LEAK TEST
TERMINAL STRENGTH
MARKING INK
MIL-STD-202, METHOD 210, TEST CONDITION B
85% RELATIVE HUMIDITY AT 85° C 250 HOURS
MECHANICAL
MIL-STD-883, METHOD 1014, TEST CONDITION C
MIL-STD-883, METHOD 1014, TEST CONDITION A
MIL-STD-202, METHOD 211, TEST CONDITION A AND C
EPOXY, HEAT CURED.
"1" LEVEL
"0" LEVEL
0 VDC
t
T
MOISTURE RESISTANCE MIL-STD 202, METHOD 106, OMIT STEP 7B
SOLDERABILITY
MIL-STD-202, METHOD 208, 95% COVERAGE
SOLVENT RESISTANCE MIL-STD-202, METHOD 2002, METHOD 215
35
+2.5 VDC
+1.5 VDC
+0.5 VDC
PART NUMBERING SYSTEM
S ERIES
CO1 (14 PIN DIP)
CO13 (8 PIN DIP)
FREQUENCY
STA B ILITY
FREQUENCY
EXTENDED
TEMPERA TURE
SY MMETRY
OPTIONS
100 ±100 PPM -
-
-
- TR TA PE A ND REEL*
050 ± 50 PPM
IN MHz
EXT
T TIGHT SY MMETRY GW GULL W ING
025 ± 25 PPM
3.3 +3.3 V
EXAMPLE: CO1100-20.000-EXT-T, CO13050-32.000-T-TR
* Available for Gull Wing only
Raltron Electronics Corporation 10651 NW 19th St. Miami, Florida 33172 U.S.A.
Tel: [phone] Fax: [phone] e-mail: [e-mail] Internet: http://www.raltron.com