Z-D250P2J Datasheet, PDF (2/2 Pages) Pulse A Technitrol Company – Z-BLOCKER® Z-D250P2J xDSL/POTS CPE Dual In-Line Filter

Z-BLOCKER® Z-D250P2J
xDSL/POTS CPE Dual In-Line Filter
Z-BLOCKER Z-D250P2J Filter Specifications
Capacitance to Ground
<0.2nF
DC Resistance
Network port at 20mA
<20 Ω
Tip and Ring to Ground at ≤ 100 Vdc
>500 MΩ
Tip and Ring to Ground at ≥ 100 Vdc and ≤ 200 Vdc
>500 MΩ
Operating Current
5 to 90 mA
Operating Voltages
Network tip to ring
0 to -100 Vdc
Network ringing signals at 30 to 115 Vrms
–100 to +100 Vdc
On-hook Voice Band Insertion Loss at 1004Hz
With 1 filter
-0.5dB to 2.2dB
With 3 filters
-1.0dB to 6.5dB
With 5 filters
-1.0dB to 6.5dB
On- or Off-hook Envelope Delay 300 Hz - 2800 Hz
<250μs
Off-hook Voice Band Insertion Loss at 1004Hz
With 1 filter
-0.5dB to 0.5dB
With 3 filters
-1.0dB to 1.0dB
With 5 filters
-1.0dB to 1.0dB
Off-hook Voice Band Insertion Loss Distortion
With 1 filter, 200 to 3400 Hz
-1.0dB to 0.5dB
With 3 filters, 200 to 3400 Hz
-1.5dB to 2.5dB
With 5 filters, 200 to 3400 Hz
-1.5dB to 2.5dB
With 1 filter, 3.4 to 4 kHz
-1.5dB to 1.0dB
With 3 filters, 3.4 to 4 kHz
-2.0dB to 3.5dB
With 5 filters, 3.4 to 4 kHz
-2.0dB to 3.5dB
Off-hook impedance distortion (5 filters)
Phone Port
SRL Low
≥13 dB
“
ERL
≥6.5 dB
“
SRL High
≥1 dB
Network Port SRL Low
≥12 dB
“
ERL
≥10 dB
“
SRL High
≥5 dB
Inter-Modulation Distortion Second and Third order products
≥57 dB and ≥60 dB,respectively
Off-hook High Band Stopband Attenuation (1 filter)
25 kHz to 50 kHz, between 20 and 90 mA
≥17 dB
50 kHz to 12 MHz, between 20 and 90 mA
≥25 dB
Bridging Loss
With 1 filter, 25 kHz to 1.2 MHz
≤0.5 dB
With 5 filters, 25 kHz to 1.2 MHz
≤1.25 dB
With 1 filter, 1.2 to 12 MHz
≤3.0 dB
With 5 filters, 1.2 to 12 MHz
≤4.0 dB
Connectors: One RJ11 jack each for DSL Modem and Phone connection, and one RJ11 plug on a 4” cord for Line connection
Dimensions: Length = 2.59in (65.9mm), Width = 1.21in (30.8mm), Height = 0.729in (18.5mm)
Compliant and listed with UL / CSA 60950, FCC CFR 47 Part 68, and IC CS-03.
12220 World Trade Drive, San Diego, CA 92128 USA
Direct: 858 674 8100, Fax: [phone]
www.excelsus-tech.com
Specifications subject to change without notice. Excelsus is a registered trade mark of Pulse Engineering, Inc.
© 2009 Pulse Engineering, Inc.
EX128.A (9/09)