PE-67200NL Datasheet, PDF (1/2 Pages) Pulse A Technitrol Company – Through Hole Current Sense Transformers

Through Hole Current
Sense Transformers
VDE Approved
Meets IEC950 insulation requirements
3750Vrms primary to secondary breakdown voltage
DVE
Frequency range 10kHz to 200kHz
Electrical Specifications @ 25°C - Operating Temperature -40°C to +130°C
DCR
Part
IPK
RT
Droop
KVI
LS
RS
Turns
KB
Number
(Amps)
(Ω)
(%)
(Volt/Amp) (mH MIN) (Ω MAX) (NS ± 1%)
KCL
REQ
(mΩ)
PE-67050
35
15
2.4
0.30
5.0
0.70
50
.269x10⁶
51.2x10^-6
.95
PE-67100
37
56
2.2
0.56
20
1.40
100
.0671x10⁶
1.56x10^-6
.85
PE-67200
38
200
2.0
1.00
80
4.50
200
.0168x10⁶
47.3x10^-9
.82
PE-67300
37
510
2.2
1.70
180
11.0
300
.00746x10⁶
6.13x10^-9
.84
NOTES:
1. These current sense transformers have a 1 turn primary winding, secondary turns (Ns) as
indicated in the table, and a 130°C insulation system.
2. The reference values are for unipolar operation, 50kHz, 40% duty factor, and an esti-
mated 55°C temperature rise.
3. The maximum useable peak sense current (I ) depends on temperature rise or core
PK
saturation, which should be evaluated for the operating conditions.
7. The terminating resistor (R ) may be varied to adjust operating flux (B ), droop, or scale
T
OP
factor (K ).
VI
8. The scale factor (K ) is proportional to the terminating resistor (R ) and is equal to 1 volt/
VI
T
amp when R =N .
TS
9. The secondary inductance (L ) is measured at 15kHz and .5V for PE-67050, 1V for
S
PE-67100, 2V for PE-67200 and 3V for PE-67300.
4. These Current Sense Transformers are recommended for switch mode power supply 10. To order RoHS compliant part, add the suffix “NL” to the part number (i.e. PE-67050
applications, unipolar or bipolar, operating at frequencies from 10kHz to 200kHz.
becomes PE-67050NL).
5. The maximum recommended operating flux density (B ) is 2000 gauss to prevent satu- 11. Pin Length for PE-67100 and PE-67100NL is equal to 0.146” +/- 0.16” (3.7mm +/- 0.4mm)
OP
ration at an operating temperature of 105°C.
for all other PNs pin length is equal to 0.200” Min (5.08mm Min).
6. The core loss factor (K ) is valid from 10kHz to 200kHz at 105°C.
CL
PE-65612NL
Mechanicals
see
note
11.
Schematics
1
TURN
1
2
Parts per package ..............................80
3
N_S TURNS
4
Dimensions:
Inches
mm
Unless
otherwise
specified,
all
tolerances
are
±
.005
0,13
For More Information
Pulse Worldwide
Headquarters
12220 World Trade Drive
San Diego, CA 92128
U.S.A.
Pulse Europe
Einsteinstrasse 1
D-71083 Herrenberg
Germany
Tel: [phone]
Fax: [phone]
Tel: [phone]
Fax: [phone]
Pulse China Headquarters
B402, Shenzhen Academy of
Aerospace Technology Bldg.
10th Kejinan Road
High-Tech Zone
Nanshan District
Shenzen, PR China 518057
Tel: [phone]
Fax: [phone]
Pulse North China
Room 2704/2705
Super Ocean Finance Ctr.
2067 Yan An Road West
Shanghai 200336
China
Tel: [phone]
Fax: [phone]
Pulse South Asia
135 Joo Seng Road
#03-02
PM Industrial Bldg.
Singapore 368363
Tel: [phone]
Fax: [phone]
Pulse North Asia
3F, No. 198
Zhongyuan Road
Zhongli City
Taoyuan County 320
Taiwan R. O. C.
Tel: [phone]
Fax: [phone] (Pulse)
Fax: [phone] (FRE)
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be
trademarks or registered trademarks of their respective owners. © Copyright, 2014. Pulse Electronics, Inc. All rights reserved.
1
pulseelectronics.com
P577.B (06/14)