P682 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – SMP MALE TO STRAIGHT TERMINATION

SMT Power Inductors
Round Wires – PG0871NL series
Current Rating: up to 28Apk
Inductance Range: 0.46uH to 10.5uH
Height: 6.4mm Max
Footprint: 7.6mm x 7.4mm Max
Part
Number
PG0871.461NL
PG0871.681NL
PG0871.821NL
PG0871.102NL
PG0871.152NL
PG0871.222NL
PG0871.332NL
PG0871.472NL
PG0871.682NL
PG0871.922NL
PG0871.103NL
Electrical Specifications @ 25°C — Operating Temperature - 40°C to +130°C ¹
Inductance
@Irated ²
(µH TYP)
Irated ³
(A)
Controlled Electical Specs
DCR ⁴
(mW)
±8%
Inductance
@ 0Adc
(µH ± 20%)
Saturation Current Isat ⁵
(A TYP)
25°C
100°C
Heating Current ⁶
Idc
(A TYP)
Core Loss ⁷
Factor
(K2)
0.42
24.0
1.5
0.46
28.0
25.0
24.0
14.196
0.64
19.0
2.3
0.68
24.5
20.0
19.0
10.647
0.71
19.0
2.3
0.82
21.0
18.0
19.0
10.647
0.80
17.5
2.3
1.00
17.5
15.5
19.0
10.647
1.20
13.5
4.4
1.5
14
12.5
13.5
8.517
2.00
9.5
7.6
2.20
12.0
10.5
9.5
7.098
3.00
7.1
13.5
3.30
10.5
9.5
7.1
5.324
4.50
6.7
17.0
4.70
9.3
8.0
6.7
4.259
6.40
5.8
20.0
6.80
7.8
6.5
5.8
3.549
8.80
4.9
30.0
9.20
6.7
5.5
4.9
3.042
9.50
4.7
31.5
10.50
6.3
5.3
4.7
2.839
NOTES:
1. Actual temperature of the component during system operation(ambient
plus temperature rise) must be within the standard operating range.
2. Inductance at Irated is a typical inductance value for the component taken
at rated current.
3. The rated current as listed is either the saturation current (@ 25°C) or the
heating current depending on which value is lower.
4. The DCR of the part is measured at an ambient temperature of 20°C±3°C
from point a and b as shown below on the mechanical drawing.
5. The saturation current, Isat, is the current at which the component induc-
tance drop by 20% (typical) at an ambient temperature of 25°C. This
current is determined by placing the component in the specified ambient
environment and applying a short duration pulse current (to eliminate
self-heating effect) to the component.
6. The heating current, Idc, is the DC current required to raise the com-
ponent temperature by approximately 40°C. The heating current is
determined by mounting the component on a typical pcb and applying
current for 30 minutes. The temperature is measured by placing the ther-
mocouple on top of the unit under test. Take note that the components’
performance varies depending on the system condition. IT is suggested
that the component be tested at the system level, to verify the tempera-
ture rise of the component during system operation.
7. Core loss approximation is based on published core data:
Core Loss = K1 * (f)^1.324* (ΔB)^2.422 in mW
K1 = 71.56 E-4
ΔB = K2 * Vusec in mT
f = switching frequency in MHz
K1 & K2 = core loss factors
V = Voltage across the component in V
Vusec = V * D /f
D = Duty cycle
8. Unless otherwise specified, all testing is made at 100kHz, 0.1Vac
9. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to
the part number (i.e. PG0871.222NL becomes PG0871.222NLT). Pulse
complies to industry standard tape and reel specification EIA481. The
tape and reel for this product has a width(W=16.0mm), pitch(Po=12.0mm)
and depth (Ko=6.8 mm).
1
pulseelectronics.com
P682.E (04/15)