P0582NL Datasheet, PDF (1/2 Pages) Pulse A Technitrol Company – THT CURRENT SENSE TRANSFORMERS

THT CURRENT SENSE
TRANSFORMERS
UL/C-UL recognized components
3000Vrms gate to drive winding test
Useful operating frequency from 50kHz to 500kHz
Most popular winding configurations
Part ⁶
Number
P0581
P0582
P0583
Electrical Specifications @ 25°C — Operating Temperature -40°C to 130°C
Turns
Ratio
200:1:1
100:1:1
50:1:1
Primary Inductance
(1-10) (mH MIN)
76
19
5
DCR Pri
(1-10) (Ω MAX)
2.8
1.4
0.7
DCR Sec1
(3-7) (mΩ ±15%)
1.7
1.7
1.7
DCR Sec2
(4-8) (mΩ ±15%)
1.7
1.7
1.7
Hi-Pot
(Pri-Sec) (Vrms)
3000
3000
3000
Additional Specifications
Part
Number
RT
Reference Data
Ipk
(Amps)
Droop
(%)
Max Flux
Density
Calculation Data
Kb
Req
(mΩ)
P0581
200
34
P0582
100
35
P0583
15
36
1.00
2000
17.12
.9
1.98
2000
68.49
.8
1.19
2000
273.97
.75
NOTES: 1. These current sense transformers have two one turn primaries that can
be used in parallel. The listed current ratings are for parallel connection.
2. The reference values are for an application using the termination resistor
(Rt) and operating with unipolar waveform at 100kHz, 40% duty cycle.
The estimated temperature rise is 55°C.
3. The peak flux density should remain below 2100 Gauss to ensure that the
core does not saturate. Use the following formula to calculate the peak
flux density: Bpk = Kb * Ipk * Rt * don/(Ff * Freq. in kHz) where: Rt is the
terminating resistor in the application and Ff is 1 for unipolar waveform
and 2 for bipolar waveform
4. To calculate the droop: Droop Exponent (D) = Rt * don/(Lpri in mH * Freq. in
kHz) %Droop = (1-e^-D) * 100
5. The temperature rise of the component is calculated based on the total core
loss and copper loss:
A. To calculate total copper loss (W): P(cu) = Ipk² * Req * Ff * don
where: Ff is 1 for unipolar waveform and 2 for bipolar waveform
B. To calculate total core loss (W): P(core) = 0.000073 * (Freq. in kHz)^1.67 *
(Bop in kG)^2.532 where: Bop in kG = Kb * Ipk * Rt * don/(2000 * Freq. in kHz)
C. To calculate temperature rise: Temperature Rise (C) = 60.18 * (Core
Loss(W) + Copper Loss (W))^.833
6. To order RoHS compliant part, add the suffix "NL" to the part number
(i.e. P0581 becomes P0581NL).
Mechanical
Schematic
.810
20,57
MAX
.580
14,73
MAX
.130
3,30
P058X
Date Code Country of Origin
3
1
10
8
For More Information:
.750 _MAX
19,05
.700
17,78
4
10
7
.350
8,89
(6X) .040
7
1
.200
4
5,08
SUGGESTED PCB HOLE PATTERN
Pri
1
50T, 100T, or 200T
10
Sec
3
1T
7
4
1T
8
Weight . . . . . . . . . . . . . . . .5 grams
Tray . . . . . . . . . . . . . . . . . . .20/tray
Dimensions: ^Inches
mm
Unless otherwise specified, all tolerances are ± ^.010
0,25
Pulse Worldwide
Headquarters
12220 World Trade Dr.
San Diego, CA 92128
U.S.A.
www.pulseeng.com
TEL: [phone]
FAX: [phone]
Pulse
Europe
Einsteinstrasse 1
D-71083 Herrenberg
Germany
Tel: [phone]
Fax: [phone]
Pulse China
Headquarters
No. 1
Industrial District
Changan, Dongguan
China
Tel: [phone]
Fax: [phone]
Pulse North China
Room 1503
XinYin Building
No. 888 YiShan Rd.
Shanghai 200233
China
Tel: [phone]
Fax: [phone]
Pulse South Asia
150 Kampong Ampat
#07-01/02
KA Centre
Singapore 368324
Tel: [phone]
Fax: [phone]
Pulse North Asia
No. 26
Kao Ching Rd.
Yang Mei Chen
Taoyuan Hsien
Taiwan, R. O. C.
Tel: [phone]
Fax: [phone]
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product
names mentioned herein may be trademarks or registered trademarks of their respective owners.
© Copyright, 2006. Pulse Engineering, Inc. All rights reserved.
www.pulseeng.com
P516.B (11/06)