PKS606YN Datasheet, PDF (1/24 Pages) Power Integrations, Inc. – PeakSwitch® Family Enhanced, Energy-Efficient, Off-Line Switcher IC With Super Peak Power Performance

Obsolete Product – Not Recommended for New Designs
PKS603-607
PeakSwitch^® Family
Enhanced, Energy-Efficient, Off-Line Switcher
IC With Super Peak Power Performance
Product Highlights
EcoSmart^®– Extremely Energy-Efficient
• Standby output power ≥0.6 W for 1 W input (high line)
• Sleep mode power ≥2.4 W at 3 W input (high line)
• No-load consumption <200 mW at 265 VAC input
• Surpasses California Energy Commission (CEC),
ENERGY STAR, and EU requirements
PeakSwitch Features Reduce System Cost
• Delivers peak power of up to three times maximum
continuous output power
• 277 kHz operation during peak power significantly
reduces transformer size
• Programmable smart AC line sensing provides latching
shutdown during short circuit, overload and open loop
faults, and prevents glitches during power down or
brownout
• Two external components reset latch on AC removal
• Adaptive switching cycle on-time extension increases low
line peak output power, minimizing bulk capacitor size
• Adaptive current limit reduces output overload power
• Frequency jittering reduces EMI filter cost
• Tight I²f tolerances and negligible temperature variation
of key parameters ease design and lower cost
• Accurate hysteretic thermal shutdown with automatic
recovery provides complete system level overload
protection and eliminates need for manual reset
Better System Cost/Performance over RCC & Discrete
• Simple ON/OFF control – no loop compensation needed
• Very low component count – higher reliability and single
side printed circuit board
• High bandwidth provides fast turn on with no overshoot
and excellent transient load response
• Peak current limit operation rejects line frequency ripple
• Built-in current limit and hysteretic thermal protection
Applications
• Inkjet printer
• Data storage, audio amplifier, DC motor drives
Description
PeakSwitch is designed to address applications with high peak-
to-continuous power ratio demands. The very high switching
frequency during peak power loads and excellent load transient
response reduce system cost as well as component count and size.
PeakSwitch incorporates a 700 V power MOSFET, oscillator,
high voltage switched current source for startup, current limit,
AC
+
IN
DC
OUT
Optional Smart _D
AC Sense
PeakSwitch
S
EN/UV
BP
Figure 1. Typical Peak Power Application.
PI-3995-051006
OUTPUT POWER TABLE
230 VAC 15%
85-265 VAC
PRODUCT³ _{Adapter Adapter Adapter Adapter}
Cont.¹ Peak² Cont.¹ Peak²
PKS603 P
13 W 32 W 9 W 25 W
PKS604 P
23 W 56 W 16 W 44 W
PKS604 Y/F 35 W 56 W 23 W 44 W
PKS605 P
31 W 60 W 21 W 44 W
PKS605 Y/F 46 W 79 W 30 W 58 W
PKS606 P
35 W 66 W 25 W 46 W
PKS606 Y/F 68 W 117 W 45 W 86 W
PKS607 Y/F 75 W 126 W 50 W 93 W
Table 1.
Notes:
1. Typical continuous power in a non-ventilated enclosed adapter
measured at +50 °C ambient.
2. Typical peak power for a period of 100 ms and a duty cycle of
10% in a non-ventilated enclosed adapter measured at +50 °C
(see Key Applications section for details).
3. See Part Ordering Information.
and thermal shutdown onto a monolithic device. In addition,
these devices incorporate auto-restart, line under-voltage sense
and frequency jittering. An innovative design minimizes audio
frequency components in the simple ON/OFF control scheme
to practically eliminate audible noise with standard varnished
transformer construction.
February 2007