|
LNK562 Datasheet, PDF (1/16 Pages) Power Integrations, Inc. – Energy Effi cient Off-Line Switcher IC for Linear Transformer Replacement | |||
|
LNK562-564
LinkSwitch®-LP
Energy Efï¬cient Off-Line Switcher IC for
Linear Transformer Replacement
Product Highlights
Lowest System Cost and Advanced Safety Features
⢠Lowest component count switcher
⢠Very tight parameter tolerances using proprietary IC
trimming technology and transformer construction
techniques enable Clamplessâ¢designs â decreases
component count/system cost and increases efï¬ciency
⢠Meets industry standard requirements for thermal overload
protection â eliminates the thermal fuse used with linear
transformers or additional components in RCC designs
⢠Frequency jittering greatly reduces EMI â enables low cost
input ï¬lter conï¬guration
⢠Meets HV creepage requirements between DRAIN and all
other pins, both on the PCB and at the package
⢠Proprietary E-Shield⢠transformer eliminates Y capacitor
Superior Performance over Linear and RCC
⢠Hysteretic thermal shutdown protection â automatic
recovery improves ï¬eld reliability
⢠Universal input range allows worldwide operation
⢠Auto-restart reduces delivered power by >85% during
short circuit and open loop fault conditions
⢠Simple ON/OFF control, no loop compensation needed
⢠High bandwidth provides fast turn on with no overshoot
and excellent transient load response
EcoSmart®â Energy Efï¬ciency Technology
⢠Easily meets all global energy efï¬ciency regulations with
no added components
⢠No-load consumption <150 mW at 265 VAC input
⢠ON/OFF control provides constant efï¬ciency to very
light loads â ideal for mandatory CEC regulations
Applications
⢠Chargers for cell/cordless phones, PDAs, power tools,
MP3/portable audio devices, shavers etc.
⢠Standby and auxiliary supplies
Description
LinkSwitch-LP switcher ICs cost effectively replace all
unregulated isolated linear transformer based (50/60 Hz) power
supplies up to 3 W output power. For worldwide operation, a
single universal input design replaces multiple linear transformer
based designs. The self-biased circuit achieves an extremely low
no-load consumption of under 150 mW. The internal oscillator
AC
IN
+ DC
Output
LinkSwitch-LP
D
FB
BP
S
(a)
PI-3923-092705
VO
Rated Output Power = VR ⢠IR
VR
IR
IO
(b) PI-3924-011706
Figure 1. Typical Application â not a Simpliï¬ed Circuit (a) and
Output Characteristic Envelope (b).
OUTPUT POWER TABLE1
PRODUCT4
230 VAC ±15%
85-265 VAC
Adapter2
Open
Frame3
Adapter2
Open
Frame3
LNK562P or G 1.9 W 1.9 W 1.9 W 1.9 W
LNK563P or G 2.5 W 2.5 W 2.5 W 2.5 W
LNK564P or G 3 W
3W
3W 3W
Table 1. Notes: 1. Output power may be limited by speciï¬c application
parameters including core size and Clampless operation (see Key
Application Considerations). 2. Minimum continuous power in a typical
non-ventilated enclosed adapter measured at 50 °C ambient. 3. Minimum
practical continuous power in an open frame design with adequate
heat sinking, measured at 50 °C ambient. 4. Packages: P: DIP-8B,
G: SMD-8B. For lead-free package options, see Part Ordering
Information.
frequency is jittered to signiï¬cantly reduce both quasi-peak and
average EMI, minimizing ï¬lter cost.
October 2005
|
▷ |