PS21542-G Datasheet, PDF (4/6 Pages) Powerex Power Semiconductors – Intellimod™ Module Dual-In-Line Intelligent Power Module (5 Amperes/600 Volts)

Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 [phone]
PS21542-G
Intellimod™ Module
Dual-In-Line Intelligent Power Module
5 Amperes/600 Volts
Electrical and Mechanical Characteristics, T_j = 25°C unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.
Typ. Max. Units
Control Sector
Supply Voltage
V_D
Applied between V_P1-V_NC, V_N1-V_NC
13.5 15.0 16.5 Volts
V_DB
Applied between V_UFB-V_UFS,
13.5 15.0 16.5 Volts
V_VFB-V_VFS, V_WFB-V_WFS
Circuit Current
I_D
V_D = 15V, V_CIN = 5V, V_DB = 15V,
—
4.25 8.50
mA
Total of V_P1-V_NC, V_N1-V_NC
V_D = 15V, V_CIN = 0V, V_DB = 15V,
—
4.95 9.70
mA
Total of V_P1-V_NC, V_N1-V_NC
V_D = 15V, V_CIN = 5V, V_DB = 15V,
—
0.50 1.00
mA
V_UFB-V_UFS, V_VFB-V_VFS, V_WFB-V_WFS
V_D = 15V, V_CIN = 0V, V_DB = 15V,
—
0.50 1.00
mA
V_UFB-V_UFS, V_VFB-V_VFS, V_WFB-V_WFS
Fault Output Voltage
V_FOH
V_SC = 0V, F_O Circuit: 10k Ω to 5V Pull-up
4.9
—
—
Volts
V_FOL
V_SC = 1V, F_O Circuit: 10k Ω to 5V Pull-up
—
0.8
1.2
Volts
V_FO(sat)
V_SC = 1V, I_FO = 15mA
0.8
1.2
1.8
Volts
PWM Input Frequency
f_PWM
T_j ≤ 125°C, T_f ≤ 100°C
—
5
—
kHz
Allowable Dead Time
t_DEAD
Relates to Corresponding Input Signal for
3
—
—
µS
Blocking Arm Shoot-through (T_f ≤ 100°C)
Short Circuit Trip Level*
V_SC(ref)
T_j = 25°C, V_D = 15V*
0.45
0.5
0.55 Volts
Supply Circuit Under-voltage
UV_DBt
Trip Level, T_j ≤ 125°C
10.0
—
12.0 Volts
UV_DBr
Reset Level, T_j ≤ 125°C
10.5
—
12.5 Volts
UV_Dt
Trip Level, T_j ≤ 125°C
10.3
—
12.5 Volts
UV_Dr
Reset Level, T_j ≤ 125°C
10.8
—
13.0 Volts
Fault Output Pulse Width**
t_FO
C_FO = 22nF
1.0
1.8
—
mS
ON Threshold Voltage (H-side)
V_th(on)
Applied between U_P, V_P, W_P-V_NC
0.8
1.4
2.0
Volts
OFF Threshold Voltage (H-side)
V_th(off)
2.5
3.0
4.0
Volts
ON Threshold Voltage (L-side)
V_th(on)
Applied between U_N, V_N, W_N-V_NC
0.8
1.4
2.0
Volts
OFF Threshold Voltage (L-side)
V_th(off)
2.5
3.0
4.0
Volts
* Short Circuit protection operates only at the low-arms. Please select the value of the external shunt resistor such that the SC trip level is less than 8.5A.
**Fault
C_FO
signal is asserted when the low-arm short circuit or control supply under-voltage
according to the following approximate equation: C_FO = (12.2 x 10^-6) x t_FO {F} .
protective
functions
operate.
The
fault
output
pulse-width
t_FO
depends
on
the
capacitance
value
of
136