PS11016 Datasheet, PDF (4/6 Pages) Powerex Power Semiconductors – FLAT-BASE TYPE INSULATED TYPE

MITSUBISHI SEMICONDUCTOR <Application Specific Intelligent Power Module>
PS11016
FLAT-BASE TYPE
INSULATED TYPE
ELECTRICAL CHARACTERISTICS (Tj = 25°C, VDH = 15V, VDB = 15V unless otherwise noted)
Symbol
fPWM
txx
tdead
Item
PWM input frequency
Allowable input on-pulse width
Allowable input signal dead time for
blocking arm shoot-through
Condition
Ratings
Min.
Typ.
Max. ^Unit
TC ≤ 100°C, Tj ≤ 125°C
—
—
15
kHz
VDH = 15V, TC = –20°C ~ +100°C (Note 3)
1
—
500
µs
Relates to corresponding inputs,
(Except brake part), TC = –20°C ~ +100°C
2.5
—
—
µs
tint
Input inter-lock sensing
Relates to corresponding input (Except break part) —
65
100
ns
VCO
Ic = 0A
VDH = 15V
1.87 2.27 2.57
V
VC+(200%) Analogue signal linearity with output current Ic = IOP(200%)
TC = –20°C ~ 100°C
0.77
1.17
1.47
V
VC–(200%)
|∆VCO| Offset change area vs temperature
Ic = –IOP(200%)
VDH = 15V, TC = –20°C ~ 100°C
(Fig. 4) 2.97 3.37 3.67
V
—
15
—
mV
VC+
Ic > IOP(200%), VDH = 15V
VC–
Analogue signal output voltage limit
—
—
0.7
V
(Fig. 4) 4.0
—
—
V
∆VC(200%) Analogue signal over all linear variation |VCO-VC±(200%)|
—
1.1
—
V
rCH
Analogue signal data hold accuracy
Correspond to max. 500µs data hold period
only, Ic = IOP(200%)
(Fig. 5)
–5
—
5
%
td(read)
Analogue signal reading time
After input signal trigger point
(Fig. 8) —
3
—
µs
ICL(H)
ICL(L)
±IOL
Signal output current of
CL operation
Idle
Active
CL warning operation level
Open collector output
VD = 15V, TC = –20°C ~ 100°C
—
—
1
µA
—
1
—
mA
(Note 4) 31.2 38.0 46.0
A
SC
OT
OTr
UVDH
Short circuit over current trip level
Over temperature
protection
Trip level
Reset level
Trip level
Tj = 25°C
VDH = 15V
(Fig. 7) (Note 5) 50.6 65.0
—
A
100
110
120
°C
—
90
—
°C
11.05 12.00 12.75 V
UVDHr
Reset level
11.55 12.50 13.25
V
OVDH
OVDHr
UVDB
Supply circuit under &
over voltage protection
Trip level
Reset level
TC = –20 ~ +100°C,
Tj ≤ 125°C
Trip level
18.00 19.20 20.15 V
16.50 17.50 18.65 V
10.0 11.0 12.0
V
UVDBr
Reset level
10.5 11.5 12.5
V
tdV
IFO(H)
IFO(L)
Fault output current
Filter time
Idle
Active
Open collector output
—
10
—
µs
—
—
1
µA
—
1
—
mA
(Note 3) : (a) Allowable minimum input on-pulse width : This item applies to P-side circuit only.
(b) Allowable maximum input on-pulse width : This item applies to both P-side and N-side circuits excluding the brake circuit.
(Note4) : CL output : The "current limit warning (CL) operation circuit outputs warning signal whenever the arm current exceeds this limit. The
circuit is reset automatically by the next input signal and thus, it operates on a pulse-by-pulse scheme.
(Note5) : The short circuit protection works instantaneously when a high short circuit current flows through an internal IGBT rising up momen-
tarily. The protection function is, thus meant primarily to protect the ASIPM against short circuit distraction. Therefore, this function is
not recommended to be used for any system load current regulation or any over load control as this might, cause a failure due to
excessive temperature rise. Instead, the analogue current output feature or the over load warning feature (CL) should be appropri-
ately used for such current regulation or over load control operation. In other words, the PWM signals to the ASIPM should be shut
down, in principle, and not to be restarted before the junction temperature would recover to normal, as soon as a fault is feed back
from its FO1 pin of the ASIPM indicating a short circuit situation.
RECOMMENDED CONDITIONS
Symbol
Item
VCC
Supply voltage
VDH, VDB Control Supply voltage
∆VDH, ∆VDB
VCIN(on)
VCIN(off)
fPWM
tdead
Supply voltage ripple
Input on voltage
Input off voltage
PWM Input frequency
Arm shoot-through blocking time
Condition
Applied across P-N terminals
Applied between VDH-GND, CBU+-CBU–, CBV+-CBV–,
CBW+-CBW–
Using application circuit
Using application circuit
Ratings
Unit
400 (max.)
V
15±1.5
V
±1 (max.)
V/µs
0 ~ 0.3
V
4.8 ~ 5.0
V
2 ~ 15
kHz
2.5 (min.)
µs
Jan. 2000