CM400YE2P-12F Datasheet, PDF (3/5 Pages) Powerex Power Semiconductors – TLI-Series (Three Level Inverter) IGBT 400 Amperes/600 Volts

Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 [phone] www.pwrx.com
CM400YE2N-12F / CM400YE2P-12F
TLI-Series (Three Level Inverter) IGBT
400 Amperes/600 Volts
Electrical Characteristics, T_j = 25°C unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.
Typ.
Inverter Part
Collector-Cutoff Current
Gate-Emitter Threshold Voltage
Gate Leakage Current
Collector-Emitter Saturation Voltage
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Total Gate Charge
Turn-on Delay Time
Turn-on Rise Time
Turn-off Delay Time
Turn-off Fall Time
Reverse Recovery Time
Reverse Recovery Charge
Emitter-Collector Voltage
External Gate Resistance
Clamp Diode Part
Repetitive Reverse Current
Forward Voltage Drop
Reverse Recovery Time
Reverse Recovery Charge
I_CES
V_GE(th)
I_GES
V_CE(sat)
C_ies
C_oes
C_res
Q_G
t_d(on)
t_r
t_d(off)
t_f
t_rr^*1
Q_rr^*1
V_EC^*1
R_G
V_CE = V_CES, V_GE = 0V
I_C = 40mA, V_CE = 10V
V_GE = V_GES, V_CE = 0V
I_C = 400A, V_GE = 15V, T_j = 25°C
I_C = 400A, V_GE = 15V, T_j = 125°C
V_CE = 10V, V_GE = 0V
V_CC = 300V, I_C = 400A, V_GE = 15V
V_CC = 300V, I_C = 400A,
V_GE1 = V_GE2 = 15V,
R_G = 4.7Ω,
Inductive Load Switching Operation,
I_E = 400A
I_E = 400A, V_GE = 0V
–
–
5
6
–
–
–
1.6
–
1.6
–
–
–
–
–
–
–
2480
–
–
–
–
–
–
–
–
–
–
–
2.6
–
–
4.7
–
I_RRM
V_R = V_RRM
–
–
V_FM
I_F = 400A
–
–
t_rr
I_F = 400A, V_CC = 300V,
–
–
Q_rr
V_GE1 = V_GE2 = 15V, R_G = 4.7Ω,
–
2.6
Inductive Load Switching Operation
Max. Units
1
7
40
2.2
–
110
7.2
4
–
700
400
1100
300
200
–
2.8
16
mA
Volts
μA
Volts
Volts
nF
nF
nF
nC
ns
ns
ns
ns
ns
μC
Volts
Ω
1
mA
2.8
Volts
200
ns
–
μC
Thermal and Mechanical Characteristics, T_j = 25°C unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.
Thermal Resistance, Junction to Case^*4
R_th(j-c')Q
Inverter IGBT
–
Thermal Resistance, Junction to Case^*4
R_th(j-c')D
Inverter FWDi
–
Thermal Resistance, Junction to Case^*4
R_th(c-f)D
Clamp Diode Part
–
Contact Thermal Resistance^*5
R_th(c-f) Thermal Grease Applied (per 1 Module) –
*4 T_C measured point is just under the chips. If using this value, R_th(f-a) should be measured just under the chips.
*5 Typical value is measured by using thermally conductive grease of λ = 0.9 [W/(m • K)].
Typ.
–
–
–
0.037
Max.
0.11
0.14
0.14
–
Units
°C/W
°C/W
°C/W
°C/W
08/10 Rev. 1
3