HZZ02002G Datasheet, PDF (5/18 Pages) Power-One – FNP1500/1800 Front-Ends FNR-3 Power Shelves Data Sheet

FNP1500/1800 Front-Ends
& FNR-3 Power Shelf Data Sheet
Output Specifications, 48Vout Models
Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated.
Parameter
Nominal output voltage Vo1
Nominal output voltage Vo2
Output voltage set point accuracy
Output voltage trimming
(via I²C or with external resistor)
FNP1500-48G
Nominal
current
output 1
FNP1800-48G
Current
limit
output 1
FNP1500-48G
FNP1800-48G
Nominal current output 2
Current limit output 2
Static line regulation output 1
Static load
regulation
FNP1500-48G
output 1
(droop
FNP1800-48G
characteristic)
Static load regulation
output 2 (droop characteristic)
Dynamic
load
regulation
FNP1500-48G
FNP1800-48G
Conditions/Description
Min
I_o = 16.1 A
I_o = 0.5 A
V_i = 230 VAC, I_o1 =16.1 A, T_C = 25 °C
-0.5
(47.8 - 48.2 VDC)
Adjustable (44.16 to 51.84 VDC)
-8
I_{o1 nom} @ V_i =105 VAC – 264 VAC, P_o 1.5 kW
I_{o1 nom} @ V_i = 85 VAC – 105 VAC, P_o 1.2 kW
I_{o1 nom} @ V_i =180 VAC – 264 VAC,
I_{o1 nom} @ V_i =105 VAC – 180 VAC,
I_{o1 nom} @ V_i = 85 VAC – 105 VAC,
I_{o1 max} @ V_i = 105 VAC – 264 VAC
I_{o1 max} @ V_i = 85 VAC – 105 VAC
P_o 1.8 kW
P_o 1.5 kW
P_o 1.2 kW
droop hiccup
droop hiccup
I_{o1 max} @ V_i = 180 VAC – 264 VAC
I_{o1 max} @ V_i = 105 VAC – 180 VAC
I_{o1 max} @ V_i = 85 VAC – 105 VAC
droop hiccup
droop hiccup
droop hiccup
I_{o2 nom} @ Vi = 85 VAC – 264 VAC, P_o 12 W
I_{o2 max} @ V_i = 85 VAC – 264 VAC
V_{i min} - V_{i max}, 50 % I_{o nom}
V_i = 230 V, 5-100 % I_{o nom}
V_o : full load (32.2 ADC) to no load
V_i = 230 V, 5-100 % I_{o nom}
V_o : full load (32.2 ADC) to no load
V_i = 230 V, 5-100 % I_{o nom}
V_o : full load (32.2 ADC) to no load
Load change 50% <─>100% I_{o nom}, dI_o/dt =1 A/s
Voltage deviation (droop + over- or undershoot)
-0.5
46.54
45.91
-5
-5.7
All models
Current
Share
Start-up time
FNP1500-48G
FNP1800-48G
Output voltage ripple and noise
(Filter 10 nF/10 µF)
Remote sense
Max. recovery time to within 1 % of V_{o1 nom}
Difference in current between two units for V_o1 above
10 % load.
Time required for output within regulation
after initial application of AC-input (V_{i nom}, I_{o nom})
after removal of inhibit
(V_{i nom}, I_{o nom})
V_{i nom}, I_{o nom}, 20 MHz bandwidth
V_o1
V_o2
Total compensation for cable losses
Nom
48
12
32.2
25.4
39.2
32.2
25.4
36.8
30
43.8
36.8
30
1.0
1.5
90.1
48
90.1
48
0.4
100
Max
+0.5
Units
VDC
VDC
% V_{o1 nom}
+8
% V_{o1 nom}
39.2
1.0
0.5
49.44
49.44
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
% V_{o nom}
mV/A
VDC
mV/A
VDC
VDC
% V_{o nom}
5
% V_{o nom}
5.7
% V_{o nom}
400
s
3.2
ADC
3.9
ADC
1.5
s
ms
480
mV_pp
120
mV_pp
500
mV
BCD.00247 Rev. AA, 07-Nov-12
Page 5 of 18
www.power-one.com