TL2105PIS Datasheet, PDF (2/2 Pages) Power-One – SIP/SIE 500 NON-ISOLATED SERIES

Powering Communications and Technology
SIP/SIE 500
NON-ISOLATED SERIES
MODELS - (See the last page of Section for options.)
Selection Chart
Model
SIP501.2LT
SIP501.5LT
SIP501.8LT
SIP502.1LT
SIP502.5LT
SIP503.3LT
Vin
(Volts)
5
5
5
5
5
5
Vin Range
(Volts)
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
Iin Max.*
(Amps)
2.3
2.7
3.1
3.5
4.0
5.1
SIE501.2LT
5
SIE501.5LT
5
SIE501.8LT
5
SIE502.1LT
5
SIE502.5LT
5
SIE503.3LT
5
4.5 - 5.5
2.3
4.5 - 5.5
2.7
4.5 - 5.5
3.1
4.5 - 5.5
3.5
4.5 - 5.5
4.0
4.5 - 5.5
5.1
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
NOTE: For Right Angle Pins, Add suffix "R" to model number.
MECHANICAL DRAWING
SIP MODEL
Vout
(Volts)
1.2
1.5
1.8
2.1
2.5
3.3
1.2
1.5
1.8
2.1
2.5
3.3
Iout Rated
(Amps)
6
6
6
6
6
6
6
6
6
6
6
6
SIE MODEL
Efficiency
Typ. **
70%
75%
77%
81%
83%
87%
70%
75%
77%
81%
83%
87%
1 23 45
6 7 8 9 10 11
0.28
(7.10)
0.100 TYP. ^{0.025 SQ.}
(2.54)
(0.64)
1.90
(48.26)
2.50
(63.5)
0.55
(14.0)
0.13 (3.30)
0.11
(2.80)
0.25
(6.40)
1 2345
6 7 8 9 10 11
0.28
(7.10)
0.10 TYP.
(2.54)
0.025 SQ.
(0.64)
1.90
(48.26)
2.50
(63.5)
0.55
(14.0)
0.13 (3.30)
0.11
(2.80)
0.25
(6.40)
123 4 5
Right Angle Pins
0.100 TYP.
0.28
(7.10)
(2.54)
1.90
(48.26)
2.50
(63.5)
6 7 8 9 10 11
0.55
(14.0)
0.025 SQ.
(0.64)
0.09
(2.30)
0.27 0.13
(6.90) (3.30)
Right Angle Pins
1 2345
0.28
(7.10)
0.10 TYP.
(2.54)
1.90
(48.26)
2.50
(63.5)
6 7 8 9 10 11
0.55
(14.0)
0.025 SQ.
(0.64)
0.27 0.13
(6.90)(3.30)
0.09
(2.30)
Thermal Impedance
Natural Convection
100 LFM
200 LFM
300 LFM
400 LFM
24.4 °C/W
18.3 °C/W
15.0 °C/W
11.1 °C/W
7.9 °C/W
Note:
Thermal impedance data is
dependent on many environmental
factors. The exact thermal
performance should be validated
for specific application.
Pin
Function
1
+Vout
2
+Vout
3
Sense (SIE)
4
5
G+Vroouunt d
6
Ground
7
+Vin
8
+Vin
9
PWR OK (SIE)
10
Trim
11
Enable
2
Tolerances
Inches:
.XX ± 0.020
.XXX ± 0.010
(Millimeters)
.X ± 0.5
.XX ± 0.25
Pin:
± 0.002
± 0.05
(Dimensions as listed unless
otherwise specified.)