LV1145BV Datasheet, PDF (2/5 Pages) Pletronics, Inc. – 6 Pad Leadless Surface Mount Oscillator

Pl tronics, Inc.
. _{19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA}
Manufacturer of High Quality Frequency Control Products
LV1145B LVDS Series
Low Voltage Differential Signal Output with Enable/Disable
6 Pad Leadless Surface Mount Oscillator
Standard Specifications
1.50 MHz – 650.00 MHz
Consult factory for higher frequencies
Overall Frequency Stability
Operating Temperature Range
Operable Supply Voltage (Vcc)
High Level Output Voltage
Low Level Output Voltage
Differential Output Voltage
Offset Voltage
Output Leakage Current
Supply Current (Icc) Enabled
Supply Current (Icc) Disabled
Symmetry (DC)
Rise and Fall Time (Tr & Tf)
RMS Jitter
± 50 PPM, ± 25 PPM and ± 20 PPM over Operating Temp. Range
0 to +80°C is standard, can be extended to - 40 to +85°C
3.3 V ± 5% standard, 5.0 V ± 10% also available
1.43 V typical and 1.60 V maximum with output enabled (100 ohm load) See Test circuit #6
0.90 V minimum and 1.10 V typical with output enabled (100 ohm load) See TC #6
247 V minimum, 330 V typical and 454 V maximum with output enabled (100 ohm load) See TC #6
1.125 V minimum, 1.25 V typical and 1.375 V maximum with output enabled (100 ohm load) See TC #6
10 uA maximum with output disabled
50 mA max < 200 MHz, 60 mA max < 500 MHz, 70 mA max 500 MHz and above
20 mA max < 200 MHz, 30 mA max < 500 MHz, 40 mA max 500 MHz and above
45/55% measured at 0°C <= Ta <= 70°C, 40/60% measured at Ta < 0°C and Ta > 70°C
1.0 nS max at 20% to 80% output swing (100 ohm load) See Test circuit #6 and Waveform #2
1.0 pS max at12 kHz to 20 MHz from the output
Enable / Disable Pin:
The Enable / Disable pin has an internal pull up and if the pin is not connected the oscilaltor is enabled. Pletronics strongly recommends
connecting the Enable / Disable pin to Vcc, if the oscillator is to be enabled at all times. In the disable condition, the output becomes a
high impedance.
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Output Enable Time
Output Disable Time
0.7 Vcc minimum at Enable / Disable Pin
0.3 Vcc maximum at Enable / Disable Pin
-20 uA maximum at Enable / Disable Pin = 0.7 Vcc
-200 uA maximum at Enable / Disable Pin = 0 V
200 nS maximum
200 nS maximum
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
Packaging
Tube or
24mm tape
16mm pitch
LV11 45 B V - 70.0M - XXX (Internal Code or blank)
Model
LV11 = E/D Pin 2
LV33 = E/D Pin 1 & 2
LV37 = E/D Pin 1
Frequency Stability
45 = ± 50 PPM
44 = ± 25 PPM
20 = ± 20 PPM
Frequency in MHz
Special Specifications (choose all that apply)
E: Extended Operating Temp Range (-40 to +85°C)
V: Supply Voltage of 3.3 volts ±5%
Y: Supply Voltage of 5.0 volts ±10%,
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Jun 2004
Pl tronics, Inc. (425) 776 -1880, Fax: [phone], [e-mail], www.pletronics.com
5