FBL2033 Datasheet, PDF (7/14 Pages) NXP Semiconductors – 3.3V BTL 8-bit latched/registered/pass-thru universal transceiver

Philips Semiconductors
3.3V BTL 8-bit latched/registered/pass-thru
universal transceiver
Product specification
FBL2033
DC ELECTRICAL CHARACTERISTICS
Over recommended operating free-air temperature range unless otherwise noted.
symbol
parameter
test conditions¹
I_OH High level output current
I_OFF Power-off output current
V_OH
High-level output
voltage
V_OL Low-level output voltage
V_IK
Input clamp voltage
I_I
Input leakage current
I_IH
High-level input current
I_IL
I_OZH
I_OZL
I_CCH
I_CCL
I_CCZ
I_CCH
I_CCL
I_CCZ
Low-level input current
Off-state output current
Off-state output current
Supply current (total)
Supply current
Supply current (total)
Supply current
B0 – B7
B0 – B7
AO0 – AO7³
AO0 – AO7³
B0 – B7
Control pins
Control/
AI0 – AI7
AI0 – AI7
Note 4
B0 – B7
B0 – B7
AO0 – AO7
AO0 – AO7
B→A
A→B
V_CC = MAX, V_IL = MAX, V_OH = 1.9V
V_CC = 0V, V_IL = MAX, V_OH = 1.9V
V_CC = 0V, V_IL = MAX, V_OH = 1.9V@85°C
V_CC = MIN to MAX; I_OH = -100µA
V_CC = MIN; I_OH = -8mA
V_CC = MIN; I_OH = -32mA
V_CC = MIN; I_OL = 16mA
V_CC = MIN; I_OL = 32mA
V_CC = MIN, I_OL = 4mA
V_CC = MIN, I_OL = 100mA
V_CC = MIN, I_I = I_IK = –18mA
V_CC = 3.6V; V_I = V_CC or 300mV
V_CC = 0V or 3.6V; V_I = 5.5V
V_CC = 3.6V; V_I = V_CC
V_CC = 3.6V; V_I = 300mV
V_CC = MAX, V_I = 1.9V
V_CC = MAX, V_I = 3.5V, note 5
V_CC = MAX, V_I = 3.75V, Note 5 @ –40°C
V_CC = MAX, V_I = 0.75V
V_CC = MAX, V_O =3V
V_CC = MAX, V_O = 0.5V
V_CC = MAX, outputs High
V_CC = MAX, outputs Low
V_CC = MAX
V_CC = MAX, outputs High
V_CC = MAX, outputs Low
V_CC = MAX
limits
min typ² max ^unit
100 µA
100
300
µA
V_CC
–0.2
V
2.4
V
2.0
V
0.4
V
0.5
V
0.5
V
0.75 1.0 1.20
–0.85 -1.2 V
±1.0
10
µA
1
–5
100 µA
100
mA
100
-100 µA
5
µA
-5
µA
14
31
mA
17
38
22
55
mA
14
32
mA
9
18
14
33
mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operation conditions for the applicable type.
2. All typical values are at V_CC = 3.3V, T_A = 25°C.
3. Due to test equipment limitations, actual test conditions are V_IH = 1.8V and V_IL = 1.3V for the B side.
4. Unused pins are at V_CC or GND.
5. For B port input voltage between 3 and 5 volt; I_IH will be greater than 100mA but the part will continue to function normally (clamping circuit
is active).
1999 Apr 15
7