87LPC767 Datasheet, PDF (52/60 Pages) NXP Semiconductors – Low power, low price, low pin count 20 pin microcontroller with 4-kbyte OTP and 8-bit A/D converter

Philips Semiconductors
Low power, low price, low pin count (20 pin)
microcontroller with 4-kbyte OTP and 8-bit A/D converter
Product data
87LPC767
DC ELECTRICAL CHARACTERISTICS
V_DD = 2.7 V to 6.0 V unless otherwise specified; T_amb = 0 °C to +70 °C, –40 °C to +85 °C, or –40 °C to +125 °C, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
MIN
TYP¹
MAX
UNIT
I_DD
Power supply current, operating
5.0 V, 20 MHz¹¹
3.0 V, 10 MHz¹¹
15
25
mA
4
7
mA
I_ID
Power supply current, Idle mode
5.0 V, 20 MHz¹¹
3.0 V, 10 MHz¹¹
6
10
mA
2
4
mA
5.0 V¹¹
I_PD
Power supply current, Power Down mode _{3.0 V11}
1
10
µA
1
5
µA
V_RAM
V_IL
RAM keep-alive voltage
Input low voltage (TTL input)
1.5
4.0 V < V_DD < 6.0 V
–0.5
2.7 V < V_DD < 4.0 V
–0.5
V
0.2 V_DD–0.1
V
0.7
V
V_IL1 Negative going threshold (Schmitt input)
–0.5 V_DD 0.4 V_DD
0.3 V_DD
V
V_IH
Input high voltage (TTL input)
0.2 V_DD+0.9
V_DD+0.5
V
V_IH1 Positive going threshold (Schmitt input)
0.7 V_DD
0.6 V_DD
V_DD+0.5
V
HYS Hysteresis voltage
0.2 V_DD
V
V_OL
Output low voltage all ports^{5, 9}
I_OL = 3.2 mA, V_DD = 2.7 V
0.4
V
V_OL1 Output low voltage all ports^{5, 9}
I_OL = 20 mA, V_DD = 2.7 V
1.0
V
V_OH
Output high voltage, all ports³
I_OH = –20 µA, V_DD = 2.7 V
I_OH = –30 µA, V_DD = 4.5 V
V_DD–0.7
V_DD–0.7
V
V
V_OH1 Output high voltage, all ports⁴
I_OH = –1.0 mA, V_DD = 2.7 V V_DD–0.7
V
C_IO
Input/Output pin capacitance¹⁰
15
pF
I_IL
Logical 0 input current, all ports⁸
V_IN = 0.4 V
–50
µA
I_LI
Input leakage current, all ports⁷
V_IN = V_IL or V_IH
±2
µA
I_TL
Logical 1 to 0 transition current, all ports^{3, 6 VIN = 1.5 V at VDD = 3.0 V}
V_IN = 2.0 V at V_DD = 5.5 V
–30
–150
–250
µA
–650
µA
R_RST Internal reset pull-up resistor
40
225
kΩ
V_BO2.5 Brownout trip voltage with BOV = 1¹²
T_amb = 0 °C to +70 °C
2.45
2.5
2.65
V
V_BO3.8 Brownout trip voltage with BOV = 0
3.45
3.8
3.90
V
V_REF Reference voltage
t_C (V_REF) Temperature coefficient
1.11
1.26
1.41
V
tbd
ppm/°C
SS
Supply sensitivity
tbd
%/V
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5 V.
2. See other Figures for details.
Active mode: I_CC(MAX) = tbd
Idle mode: I_CC(MAX) = tbd
3. Ports in quasi-bidirectional mode with weak pull-up (applies to all port pins with pull-ups). Does not apply to open drain pins.
4. Ports in PUSH-PULL mode. Does not apply to open drain pins.
5. In all output modes except high impedance mode.
6. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when
V_IN is approximately 2 V.
7. Measured with port in high impedance mode. Parameter is guaranteed but not tested at cold temperature.
8. Measured with port in quasi-bidirectional mode.
9. Under steady state (non-transient) conditions, I_OL must be externally limited as follows:
Maximum I_OL per port pin:
20 mA
Maximum total I_OL for all outputs:
80 mA
Maximum total I_OH for all outputs:
5 mA
If I_OL exceeds the test condition, V_OL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
10. Pin capacitance is characterized but not tested.
11. The I_DD, I_ID, and I_PD specifications are measured using an external clock with the following functions disabled: comparators, brownout
detect, and watchdog timer. For V_DD = 3 V, LPEP = 1. Refer to the appropriate figures on the following pages for additional current drawn by
each of these functions and detailed graphs for other frequency and voltage combinations.
12. Devices initially operating at V_DD = 2.7 V or above and at f_OSC = 10 MHz or less are guaranteed to continue to execute instructions correctly
at the brownout trip point. Initial power-on operation below V_DD = 2.7 V is not guaranteed.
2001 Aug 07
49