|
TDA8942P Datasheet, PDF (19/23 Pages) NXP Semiconductors – 2 x 1.5 W stereo Bridge Tied Load BTL audio amplifier | |||
|
◁ |
Philips Semiconductors
TDA8942P
2 x 1.5 W stereo BTL audio ampliï¬er
18. Revision history
Table 11: Revision history
Rev Date
CPCN Description
02 20000314 -
Product speciï¬cation; second version; supersedes initial version TDA8942P-01 of
14 April 1999 (9397 750 04879). Modiï¬cations:
⢠Table 1 on page 1:THD: Max value 0.1% changed to â 0.3%;
SVRR: Typ value 65 dB â added
⢠Ordering options removed
⢠Figure 1 on page 2: Block diagram; pin numbers changed OUT2â â 7 and OUT2+ â 10
⢠Figure 2 on page 3: Pin conï¬guration; pin numbers changed OUT2â â 7 and OUT2+ â 10
⢠Table 3 on page 3: Pin description; pin numbers changed OUT2â â 7 and OUT2+ â 10
⢠Section 8 âFunctional descriptionâ:
â Section 8.1 âInput conï¬gurationâ on page 4 â added.
â Section 8.2 âPower ampliï¬erâ on page 5: ........, capable of delivering a peak output
current of 1.5 A â changed to 2 A.
â Section 8.2.1 âOutput power measurementâ on page 5 â added
â Section 8.2.2 âHeadroomâ on page 5 â added
⢠Section 8.3 âMode selectionâ:
â Standby mode: VMODE > (VCC â 0.5 V) â changed to (VCC â 0.5 V) < VMODE < VCC; The
power consumption of the TDA8942P will be reduced to <0.18 mW â added.
â Mute mode: the DC level of the input and output pins remain on half the supply
voltage â added;
â 2.5 V < VMODE < (VCC â 1.5 V) â changed to 3 V < VMODE < (VCC â 1.5 V)
â Section 8.3.1 âSwitch-on and switch-offâ on page 6 â added.
⢠Section 8.4 âSupply Voltage Ripple Rejection (SVRR)â on page 6 â added
⢠Section 8.5 âBuilt-in protection circuitsâ on page 6 â added
⢠Table 5 on page 7:
â Ptot value added 2.2 W
â VCC(sc) value added 12 V
⢠Table 6 on page 7: Rth(j-a) value 55 K/W changed to â 57 K/W
⢠Table 7 on page 7: VMODE - mute mode - value Min 2.5 â changed to 3 V
⢠Table 8 on page 8:
â THD: Max value 0.1% changed to â 0.3%
â SVRR; Typ values 65 and 60 dB â added
â αcs; Typ value 75 dB â added
â Rsource changed to â RS in table and associated table notes; Value added RS = 0 â¦;
â Table note [2]: .... 100 mV (RMS).... changed to â ... 700 mV (RMS)....
⢠Figure 3 to 13: ï¬gures added
⢠Section 13 âInternal circuitryâ on page 13: â added
⢠Figure 14: ï¬gure modiï¬ed
9397 750 06862
Product speciï¬cation
Rev. 02 â 14 March 2000
© Philips Electronics N.V. 2000. All rights reserved.
19 of 23
|
▷ |