PSA60-105_14 Datasheet, PDF (1/2 Pages) Phihong USA Inc. – PSA60 Series Switching power Supply

WWW.PHIHONG.COM
80W* Universal Input Series
PSA60 Series Switching power Supply
*80W rated at 20CFM air flow cooling.
Features
 High efficiency
 Built-in EMI filter
 Over voltage protection
 Short circuit protection
Applications
 Disk/Tape drive systems
 Microprocessor systems
 Peripheral equipment
 Mixed logic applications
Safety Approvals
 cUL 1950
 TUV EN60950
 CSA 22.2 234
 CE (Low Voltage Directive)
Mechanical Characteristics
 Length: 127mm (5in)
 Height: 40.0mm (1.58in)
 Width: 76.2mm (3in)
 Weight: 360g (4.7oz)
Output Specifications
Model ⁽²⁾
DC Output
Voltage
Min.
Load ⁽¹⁾
Max.
At 20CFM
Ripple
P-P ⁽³⁾
Total
Regulation
Output
Pins
PSA60-105
+5V
0.0A
10A
10A
100mV
±2%
1,2,3
PSA60-112
+12V
0.0A
5.0A
6.6A
120mV
±2%
1,2,3
PSA60-115
+15V
0.0A
4.0A
5.3A
150mV
±2%
1,2,3
PSA60-124
+24V
0.0A
2.5A
3.3A
240mV
±2%
1,2,3
PSA60-148
+48V
0.0A
1.2A
1.4A
300mV
±2%
1,2,3
PSA60-202
+5V (V1)
+24V (V2)
1.0A
0.1A
6.0A
1.3A
8.0A
50mV
±2%
1.8A
240mV
±5%
2,3
1
PSA60-203
+5V (V1)
+12V (V2)
1.0A
0.3A
4.0A
3.5A
6.0A
50mV
±2%
4.5A
120mV
±5%
2,3
1
+5V (V1)
1.0A
6.0A
8.0A
50mV
±2%
2,3
PSA60-301 +12V (V2)
0.3A
2.2A
3.0A
120mV
±5%
1
-12V (V3)
0.0A
0.3A
0.5A
120mV
±5%
6
+5V (V1)
1.0A
6.0A
8.0A
50mV
±2%
2,3
PSA60-302 +12V (V2)
0.1A
1.2A
1.8A
120mV
±5%
1
-12V (V3)
0.1A
1.2A
1.8A
120mV
±5%
6
+5V (V1)
1.0A
6.0A
8.0A
50mV
±2%
2,3
PSA60-303 +12V (V2)
0.3A
2.2A
3.0A
120mV
±5%
1
-5V (V3)
0.0A
0.5A
0.5A
50mV
±5%
6
+5V (V1)
1.0A
6.0A
8.0A
50mV
±2%
2,3
PSA60-304 +15V (V2)
0.3A
1.5A
2.0A
150mV
+10%/-3%
1
-15V (V3)
0.0A
0.5A
0.5A
150mV
±5%
6
* Total output power must not exceed 60W at convection cooling and 80W at 20CFM air flow cooling.
(1) Peak output current lasting less than 30 seconds with duty cycle less than 10%. During peak loading, peak total power must not exceed 80W.
(2) Minimum order quantity of 1000 pieces is required when ordering this series
(3) Ripple & noise is measured at 20MHz bandwidth limit by use a 12 inch twisted wire terminated with a 10uF capacitor in parallel 0.1uF ceramic
capacitor.
Phihong is not responsible for any error, and reserves the right to make changes without notice. Please visit our website at www.phihong.com for the
most up-to-date specifications and contact information.
Revised 10/16/2013